Kinetic Monte Carlo simulations of radiation induced segregation and precipitation

Kinetics of radiation induced segregation and precipitation in binary alloys are studied by Monte Carlo simulations. The simulations are based on a simple atomic model of diffusion under electron irradiation, which takes into account the creation of point defects, the recombination of close vacancy-interstitial pairs and the point defect annihilation at sinks. They can reproduce the coupling between point defect fluxes towards sinks and atomic fluxes, which controls the segregation tendency. In pure metals and ideal solid solutions, the Monte Carlo results are found to be in very good agreement with classical models based on rate equations. In alloys with an unmixing tendency, we show how the interaction between the point defect distribution, the solute segregation and the precipitation driving force can generate complex microstructural evolutions, which depend on the very details of atomic-scale diffusion properties.     

鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.     

A geometry-based error estimation for cross-ratios

For choosing specific cross-ratios as 2D projective coordinates in various computer vision applications, a reasonable error analysis model is usually required. This investigation adopts the assumption of normal distribution for positioning errors of point features in an image to formulate the error variances of cross-ratios. Based on a geometry-based error analysis, a straightforward way of identifying the cross-ratios with minimum error variances is proposed. Simulation results show that the proposed approach, as well as a further simplified alternative, yield much better estimations of minimum error variances in terms of accuracy, cost, and stability compared with some other methods, e.g., the one based on the rule given by Georis et al. (IEEE Trans. Pattern Anal. Mach. Intell. 20 (4) (1998) 366). Some causes of the performance differences in the estimations are explained using a special configuration of point features.     

The mirror effect and mixture signal detection theory.

The mirror effect for word frequency refers to the finding that low-frequency words have higher hit rates and lower false alarm rates than high-frequency words. This result is typically interpreted in terms of conventional signal detection theory (SDT), in which case it indicates that the order of the underlying old item distributions mirrors the order of the new item distributions. However, when viewed in terms of a mixture version of SDT, the order of hits and false alarms does not necessarily imply the same order in the underlying distributions because of possible effects of mixing. A reversal in underlying distributions did not appear for fits of mixture SDT models to data from 4 experiments. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Shape-Controlled Synthesis and Upconversion Luminescence of Y2O3:Yb, Er Microstructures

The Y2O3: Yb3 , Er3 microstructures were fabricated by a hydrothermal method without surfactants.The microstructures structure was characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM,KYKY 1000B).The up-conversion luminescence spectra were studied under 978 nm laser diode excitation.In Yb3 and Er3 codoped Y2 O3 microcrystals, the relative intensity of green emission became stronger as the morphology of sample changed from wires to films.     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

Characterization of two-phase nickel aluminides produced by pressure-assisted combustion synthesis

Two-phase (B2+L1₂) nickel aluminide intermetallic compounds were synthesized by the pressure-assisted volume combustion synthesis (CS). The production and characterization of the samples containing NiAl+Ni₃Al were investigated. Aluminum (99% pure, 15 μm) and carbonyl nickel (99.8 pure, 4-7 μm) powders were used. The production of intermetallic compound was carried out at 1050 °C under 150 MPa uniaxial pressure in open air atmosphere in an electrical resistance furnace for 60 min. The formation temperature of intermetallic compound was determined by differential scanning calorimeter (DSC) analysis, and exothermic temperature of powder mixture was determined as 653 °C. The characterization of samples was confirmed by optical microscope, SEM and XRD analysis. It was observed that the structure of compound has very low porosity and the formation of NiAl was completed successfully. The relative density of test materials measured according to Archimedes’ principle was 98.04%. The microhardness of test materials was about 351 HVN₁.     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.