Influence of chromium on the local structure and morphology of ferric oxyhydroxides

The extended X-ray absorption fine structure (EXAFS) method and transmission electron microscopy (TEM) have been used for characterizing the local structure and morphology of ferric oxyhydroxides, α-FeOOH and γ-FeOOH, with and without chromium. These ferric oxyhydroxide powders were prepared from aqueous solutions containing iron and chromium ions. Radial structural functions for iron obtained by Fe K edge EXAFS spectra showed that the linkage of structural units formed by FeO₆ octahedra in γ-FeOOH is distorted by chromium addition, while such distortion in α-FeOOH is not clearly detected. On the other hand, Cr K edge EXAFS spectra showed that the local structure around chromium does not necessarily correspond to the local structure around of iron, which is observed by Fe K edge EXAFS spectra. This suggests that the structural units containing iron and chromium are heterogeneously distributed in these ferric oxyhydroxides. The local structural information was discussed coupled with morphological features of these ferric oxyhydroxides observed by TEM.     

基于I2C总线技术的等离子喷焊系统的研究

阐述了基于I^2C总线技术的等离子喷焊过程控制系统的设计原理，介绍了软硬件及接口设计技术。实践表明，采用I^2C总线技术，不仅使系统的芯片大大减少，系统的灵活性增强，而且提高了系统的抗干扰能力。     

Impact of transient chemistry on the corrosion potential of a steam turbine disc steel

The adoption of two-shifting in coal-fired power generation (switching from on-load to off-load conditions on a daily basis and off-load for the weekend) results in regular cycling of the solution chemistry of the condensed steam on the turbine discs. A first stage investigation has been made of the effect of such chemistry cycling on the corrosion potential of the disc steel. The corrosion potential is typically about +0.05 V (SCE) in off-load chemistry (aerated pure water) and below −0.6 V (SCE) in on-load chemistry (deaerated solution containing chloride or chloride and sulphate anions). The critical observation was the sluggish response of the corrosion potential upon restoration of deaerated on-load conditions with the implication of a likely increase in pit and stress corrosion crack development.     

Effects of electrical discharge surface modification of superalloy Haynes 230 with aluminum and molybdenum on oxidation behavior

The effects of the electrical discharge alloying (EDA) process on improving the high temperature oxidation resistance of the Ni-based superalloy Haynes 230 have been investigated. The 85 at.% Al and 15 at.% Mo composite electrode provided the surface alloying materials. An Al-rich layer is produced on the surface of the EDA specimen alloyed with positive electrode polarity, whereas, many discontinuous piled layers are attached to the surface of the EDA superalloy when negative electrode polarity is selected. The oxidation resistance of the specimen alloyed with positive electrode polarity is better than that of the unalloyed superalloy, and the effective temperature of oxidation resistance of the alloyed layer can be achieved to 1100 °C. Conversely, the oxidation resistance of the other EDA specimen alloyed with negative electrode polarity is even worse than that of the unalloyed superalloy.     

Leaded brass rods C 38500 for automatic machining operations: A technical report

C 38500 is a widely used copper alloy with a great variety of applications from decoration and architecture to mechanical/electrical engineering. The chemical composition of this alloy offers superior machinability and subsequently increased productivity in high-speed machining and manufacturing processes. In European countries, this alloy is used primarily as free cutting brass (CW 614N according to EN 12164: 1998), similar to C 36000 alloy, which is used also for thread rolling. The lower percentage of Cu compared to C 36000 (nominal 58% instead of 61%) decreases the cost of the raw materials. This paper reports the principal aspects of microstructure, mechanical properties, and machinability of this alloy in relation to the industrial manufacturing process used.     

Evaluation of the coupled multielectrode array sensor as a real-time corrosion monitor

Coupled multielectrode array sensors made of carbon steel and stainless steels were evaluated and compared with electrochemical noise (EN) sensors. Good correlations between sensor signals and solution corrosivity were observed for all multielectrode array sensors. Some correlation between the average pit index and solution corrosivity was observed for the carbon steel EN sensors, but not for the stainless steel EN sensors. The time-average noise resistances from the stainless steel EN sensors correlate well with solution corrosivity. There were, however, large random fluctuations and drifting for all EN signals, which make the EN sensors unreliable as real-time monitors.     

有关C语言教学方法优化的探讨

C语言程序设计是一门重要的课程,却难学难教。教学方法优化十分必要。教学方法优化应从激发学生兴趣入手,采用循序渐进的方式,着重培养学生举一反三的编程能力,引导学生写出高质量的程序,并丰富考核方式。     

基于嵌入式电脑横机控制系统

本文分析了电脑横机的结构与功能,提出了基于嵌入式的电脑横机控制系统,采用了S3C2410为主处理芯片,通过FPGA扩展端口,系统读取织物花型数据,控制横机各个动作子系统来完成编制动作,该电脑横机控制系统与传统电脑横机系统相比较,工作效率高,可移植性强。     

公交车的远卡自动收费系统设计

在对公交收费系统的发展和无线射频识别技术进行研究的基础上,分析了现行公交收费系统的优缺点与局限性,并提出了一种公交车远卡自动收费系统的设计思路.主要使用ARM核芯片STM32、射频芯片nRF24LE1等器件,完成了硬件设计.在软件设计上实现了自动计算票价的扣费机制.该系统创新性地将远距离射频技术应用在公交收费系统中,不仅方便了乘客,而且大大提高了乘客上下车的效率.     

利用SQLServer实现局域网软件自动升级

介绍了一种只利用SQLServer,无需其他专门服务器就可以轻松实现的局域网软件自动升级方法。