乙醇对溶胶-凝胶法制备SiO_2溶胶性能的影响

以HNO3为催化剂,用正硅酸乙酯(TEOS)溶胶-凝胶工艺制备纳米多孔二氧化硅薄膜。较详细地研究了工艺参数乙醇/TEOS摩尔比对溶胶性能的影响.结果表明,随着乙醇/TEOS摩尔比的增大,溶胶粘度减小,凝胶时间变长,胶体粒径有变小趋势。     

基于Pro／E参数化斜齿轮建模技术

应用Pro／E软件的参数化造型功能，不需要二次开发，直接创建渐开线斜齿圆柱齿轮模型，对直齿、人字齿齿轮的建模具有借鉴作用。     

PA6/SANMAH/GF复合材料的制备及其性能研究

采用双螺杆挤出机通过熔融共混制备了尼龙6／（苯乙烯／丙烯腈／顺丁烯二酸酐）共聚物／玻璃纤维（PA6／SANMAH／GF）复合材料，测试了材料的拉伸强度、弯曲强度、弯曲弹性模量、缺口冲击强度、热变形温度、吸水率、熔点和熔融焓，并与GF增强PA6（PA6／GF）复合材料和GF增强PA6／（苯乙烯／丙烯腈）共聚物（PA6／SAN／GF）复合材料进行了性能对比。结果表明，在PA6与SANMAH的质量比为100：3—30时，PA6／SANMAH／GF复合材料的拉伸强度与PA6／GF复合材料相当，但高于PA6／SAN／GF复合材料，弯曲强度和弯曲弹性模量高于PA6／GF和PA6／SAN／GF复合材料．缺口冲击强度高于PA6／GF复合材料，但低于PA6／SAN／GF复合材料；在PA6与SANMAH的质量比为100：40时，PA6／SANMAH／GF复合材料的拉伸强度、弯曲强度和缺口冲击强度明显降低；在整个试验范围内，PA6／SANMAH／GF复合材料的热变形温度比PA6／GF和PA6／SAN／GF复合材料低4～7℃；吸水率随着SAN-MAH用量的增加而逐渐减小。     

New Process for the Preparation of Monodispersed, Spherical Silica Particles

A new method is presented for preparing highly monodispersed silica particles using a two-stage semibatch/batch hydrolysis reaction of Si(OC₂H₅)₄. The slower rate of hydrolysis of the tetraethylorthosilicate (TEOS) that occurred during the semibatch process resulted in larger silica particles with a higher yield and narrower size distribution. This was in direct contrast to the batch process. In addition, the ability of four different mixed processes to produce silica particles with good packing density, narrower particle-size distribution, and higher yield were evaluated. These were batch/batch (B-B), batch/semibatch (B-S), semibatch/batch (S-B), and semibatch/semibatch (S-S) processes. The S-S system produced the largest particles with the highest yields. The size of the silica particles obtained by the S-B method decreased with increasing reaction time, while the particles obtained by the B-S process had the best particle-size distribution and packing density. In conclusion, a mixed batch/semibatch system was the best way to produce an extremely narrow particle-size distribution and a good packing density.     

Premodification of Pt/γAl2O3 with Cinchonidine for the Enantioselective Hydrogenation of Ethyl Pyruvate: Effect of Premodification Conditions on Reaction Rate and Enantioselection

The premodification of a 5 wt% Pt/-Al₂O₃ catalyst with cinchonidine (0.01 and 0.2 g g^-1 _catalyst) is described and discussed. Premodification is carried out by treating the catalyst with a solution of cinchonidine followed by solvent removal. Catalysts premodified in this way give the same ee and initial rate of reaction for the enantioselective hydrogenation of ethyl pyruvate as those using the standard in situ modification procedure. Investigations of different solvents for premodification and reaction (dichloromethane, ethanol) show that it is the solvent used for the reaction that controls the observed enantioselection. Premodified catalysts also display the initial transient behavior typically observed with in situ modified catalysts in which the ee increases with conversion in the early part of the reaction. Premodified catalysts show an enhanced rate of reaction when ethanol is used as the reaction solvent compared with in situ modified catalysts under the same conditions. Premodification using aerobic conditions gives the best results and premodified catalysts can be stored prior to use for up to a week without loss of catalytic performance.     

固体超强酸SO2-4/TiO2-SiO2催化合成马来酸二辛酯

用H2SO4浸渍钛硅复合氧化物，制得固体超强酸SO4^2-/TiO2-SiO2，考察了催化剂对马来酸酐与正辛醇的酯化反应的催化作用及其制备条件对催化剂活性的影响，并与硫酸，对甲苯磺酸的催化效果比较，结果表明，对于给定反应，当n(Ti):n(Si)为15：1，用浓度0．6mol/L的硫酸浸渍8h，在550℃下焙烧3h时制得的催化剂SO4^2-/TiO2-SiO2具有最高的催化活性，用以催化马来酸酐和正辛醇的酯化反应，可得无色透明的酯化产物，3h内酯化率达99．1％，较SO4^2-/TiO2催化剂的酯化率提高了约6％。     

氟丙防腐涂料的耐候性研究

运用冷拼法制备氟丙树脂并配制了氟丙防腐涂料,比较研究了其与氟碳树脂涂料、含羟基丙烯酸树脂涂料性能及耐老化性能。结果表明:氟丙涂料比氟碳涂料具有更高的光泽度,比丙烯酸涂料有更好的耐候性,树脂含氟量与涂料的光泽度和失光率之间存在线性对应关系,含氟量增加,光泽度和失光率均线性降低。     

皮革涂料用丙烯酸酯核-壳乳液的研制

采用种子乳液聚合法，以交联型软性聚合物为核，交联型硬性高聚物为壳，合成了具有优异耐寒性及高温抗回粘性聚合物。讨论了乳化剂种类及应用、核／壳比等对聚合物性能的影响。     

Chemical and microstructural investigation of Pt/CeO2 catalysts reduced at temperatures ranging from 473 to 973 K

The combined application of chemical techniques and HREM shows that platinum deactivation in Pt/CeO₂ catalysts steadily increases with the reduction temperature (T_r: 473–1173 K). Though no suppression of the H₂ adsorption was observed, the TPD-H₂ traces indicate the occurrence of significant chemical changes with T_r. As revealed by HREM, the metal decoration starts at T_r: 973 K, a temperature well above those at which the chemical effects can be observed.     

电子束辐照和氢氧化铝对LLDPE/EVA共混物凝胶含量和力学性能的影响

研究了电子束辐照剂量和氢氧化铝(ATH)的含量对线性低密度聚乙烯(LLDPE)/乙烯-醋酸乙烯酯(EVA)共混物凝胶含量和力学性能的影响。辐照剂量是影响LLDPE/EVA/ATH阻燃体系凝胶含量的主要因素,而ATH对其凝胶含量的影响较小。随着ATH含量的增加,LLDPE/EVA共混物的拉伸强度逐步增加,断裂伸长率迅速下降。所有阻燃体系的拉伸强度均是随着辐照剂量的增加而逐步增大,但辐照剂量对这些阻燃体系的断裂伸长率的影响却比较复杂。