正弦波下砂岩ms级损伤预测模型

为获得毫秒(ms)级正弦波损伤变量预测模型,对岩样在不破坏情况下进行了不同波形不同频率的轴向力加卸载试验。提出了不同步时间段的定义,进而获得不同峰值荷载下不考虑不同步时间条件下的动态泊松比分别与即时荷载、即时横向长度、即时轴向高度之间的线性关系,从而得到线性关系中系数与峰值荷载间的拟合公式,即可联立不同已知条件,通过少量几个加载力峰值下的试验数据,对任意峰值荷载下动态泊松比与相关参数间的线性关系进行预测。以此为基础研究得到,在误差允许的范围内,采用动态泊松比与即时横向长度的线性关系,推导出体积应变、损伤变量的计算公式和方法,可以很好地对加卸载过程中岩样的体积应变、损伤的变化做出ms级的精确预测,也为在已知少量循环试验下获得岩石动态参数,即可对ms级的损伤进行精确预测的模型提供了方法。     

考虑接触行为的U型渠道冻胀数值模拟

U型衬砌渠道具有良好的整体性和冻胀适应性,但在冬季仍极易因土体冻胀而导致破坏。考虑渠基冻土与衬砌接触面冻结的非线性特性和冻土、混凝土材料的塑性特征,建立能分析渠道基土与衬砌间挤压、脱开及滑移等接触力学行为的渠道冻胀破坏热力耦合数值模型。以宝鸡峡灌区塬下北干渠为原型渠道,按照模型是否考虑接触分别进行冻胀数值模拟,并对模拟结果进行对比分析。结果表明:考虑接触的模型模拟结果与原型实测值更相符,更能合理地解释U型渠道冻胀在渠底与阴坡衔接处冻胀量最小;考虑接触的混凝土塑性应变最大值是不考虑接触时的3.76倍;考虑接触的法向冻胀力和切向冻结力更均匀,最大值均减少1.5~3.0倍,应力集中现象减弱,更能反映混凝土衬砌板与渠基土之间的滑移变形与破坏准则的相互作用。研究结果为U型衬砌渠道冻胀破坏规律提供了分析方法。     

基于应变率损伤本构模型的围岩分区破裂化现象数值模拟

为了探究深部巷道围岩的分区破裂化现象,利用ANSYS/LS-DYNA软件数值模拟,使用Cowper-Symonds本构模型结合GISSMO模型,将巷道的开挖视为动力过程。从岩石的细观角度出发,考虑岩石的应变率效应以及损伤对岩石的力学性质的影响,构建应变率损伤本构模型。同时结合应力三轴度,以更全面地描述岩石在各种应力条件下的力学特性,并基于最大应变和最大拉应力准则建立单元破坏准则。对岩石进行单轴压缩数值、掘进开挖法模拟及实际观测的结果表明:岩石单轴压缩全应力-应变曲线拟合效果较好;掘进开挖速率对分区破裂化现象有影响;掘进开挖法的分区破裂化模拟结果与实际观测数据具有一定的一致性。提出的模型对于围岩分区破裂化现场的模拟及预测有一定的参考意义。     

基于模型缩聚的θ指标损伤识别方法

为实现大型三维空间结构的损伤检测,提出了一种基于模型缩聚技术的检测方法。该方法利用有限数量的加速度传感器,得到大型三维桁架结构的自振频率和模态振型,以完成损伤的识别。数值仿真结果表明：该方法在损伤的定位识别和定量识别上能达到预期的适用性和可靠性。     

The Impact of Fluid Dynamic Stress in Stirred Bioreactors – The Scale of the Biological Entity: A Personal View

From the start of industrial biotechnology, there has been a perception that biological entities are damaged by stirring, so-called ‘shear damage'. Often, it was the soft option to explain a loss of performance when it was due to other factors, such as bubble ingestion with proteins or on scale-up, where tip speed increased when it was due to decreased homogeneity, especially in pH. For many years, poor control and the range of analytical tools available made a more in-depth explanation difficult; and the concepts of ‘high' and ‘low shear' impellers, now largely disproven, increased it. Here, the size of the biological entity is compared to the Kolmogorov microscale of turbulence leading to a reasonably clear picture emerging. The article starts with the author's introduction to the issue approximately 42 year ago with enzymes, conveniently also the smallest entity; and finishes with the largest, filamentous fungi.     

Fatigue Delamination Characteristics of Plasma Sprayed Coatings under Fretting

FRETTING is referring to a reciprocating motion withthe small displacement between two components incontact[1].Fretting wear is superficial materialremoval during the fretting.It severely reduces theperformance,efficiency and service lifetime of thecomponents[2],Thermal spraying has been employedto enhance the fretting wear resistance of components,and the fretting wear behavior of the coatings has beenalso explored.However,the experimental results wereoften contradictive and confusing.On …     

不同应力状态下铝合金变形及损伤机理的研究

利用改装的Arcan夹具对铝合金（6063）的蝶形试样进行0°，30°，45°，60°，90°的拉伸及拉伸卸载试验，研究了铝合金在不同应力状态下变形及损伤机理。结果表明：铝合金在不同应力状态下的工程应力一应变曲线明显不同。0°加载时，在蝶形中心产生微孔洞，微孔洞之间剪切，从而产生了微裂纹。随着微裂纹的扩展、连接导致试样断裂。随着试样中三轴应力度的减小，在蝶形试样中心的剪切应力不断增大，同时在蝶形试样中的剪切变形带越来越集中。显微裂纹首先在剪切带中产生，随着微裂纹的扩展导致试样的断裂。90°拉伸时，在蝶形中心形成明显的剪切变形带。90°加载时，在试样中产生的剪切带是形变剪切带而非相变剪切带。利用有限元软件ABAQUS对不同角度拉伸试验进行模拟，从而得出了不同应力状态下的塑性区的形状和大小。     

Failure analysis of beta-C titanium alloy high-pressure vessels

An attempt has been made to apply the linear elastic fracture mechanics concept to Beta-C titanium alloy pressure vessels that exhibited brittle fractures during hydrotesting. Based on the results of stress analysis on the real structures and fracture surface examinations, a stress-intensity factor,K _IC, was estimated. TheK _IC value of the material in the cracking direction was measured by a surface semi-elliptical crack method. It was found that theK _IC value of the material is very close to the estimated stress-intensity factorK _I during failure, which places the pressure vessels in a critical condition in that a small variation in flaw size may cause a catastrophic failure. A compromise must be made betweenK _IC and the required yield strength. In this restricted case, the yield strength of the material should be controlled in the range of 1150 to 1200 MPa to avoid brittle fracture and the possible occurrence of yield during hydrotesting. Control of microstructure and other mechanical properties is also discussed in this investigation.     

稀土对D型石墨铸铁强化机理的研究

通过试验研究,发现微量稀土能促进D型石墨铸铁中初晶奥氏体骨架的生长,对强化基体组织有一定的作用。微量稀土能细化D型石墨,石墨数量增多,石墨生长前端钝化、分枝、花瓣状形态也有所改善,大大减轻了石墨对基体的破坏作用,从而提高D型石墨铸铁的力学性能。     

相控阵超声检测技术在碳纤维结构分层缺陷检测中的试验

以碳纤维层压结构中容易产生的分层缺陷为研究对象,采用相控阵超声检测技术进行CIVA仿真和检测试验。通过声场及缺陷的建模和CIVA仿真检测试验,得出了碳纤维层压结构分层缺陷的理想检测参数。设计制作了模拟分层试验件,并进行实际检测试验,结果表明相控阵超声技术可以有效地检测该类缺陷。