Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

Measurement of the Timoshenko Shear Stiffness. II: Effect of Transverse Compressibility

This is the second of two papers devoted to the issue of measuring the Timoshenko shear stiffness of thin-walled composite beams. In the first paper, the effect of warping on the effective Timoshenko shear stiffness, as measured through bending tests, was studied. The bending test was simulated using finite-element analysis, and the results indicated that the warping effect was minimal. On the other hand, the evidence suggests that transverse flexibility may have a significant influence on the effective Timoshenko shear stiffness, decreasing the effective shear stiffness at shorter test spans. The purpose of the present study is to further investigate this effect and to explore the use of a sandwich theory to predict the measurement error. A higher-order sandwich theory, which captures the transverse strain at concentrated loads and supports, is applied to a commercially available thin-walled composite beam. The results indicate that the sandwich model does capture the decrease in the effective shear stiffness at short spans, and the dependence of the shear stiffness on span-to-depth ratio is similar to that calculated in the first paper, using the finite-element method.     

Significance of the elastic peak stress evaluated by FE analyses at the point of singularity of sharp V-notched components

The paper presents an expression useful to estimate the notch stress intensity factor (NSIF) from finite element analyses carried out by using a mesh pattern with a constant element size. The evaluation of the NSIF from a numerical analysis of the local stress field usually requires very refined meshes and then large computational effort. The usefulness of the presented expression is that (i) only the elastic peak stress numerically evaluated at the V‐notch tip is needed and no longer the whole stress–distance set of data; (ii) the adopted meshes are rather coarse if compared to those necessary for the evaluation of the whole local stress field. The proposed expression needs the evaluation of a virtual V‐notch tip radius, i.e. the radius which would produce the same elastic peak stress than that calculated by FEM at the sharp V‐notch tip by means of a given mesh pattern. Once such a radius has been theoretically determined for a given geometry, the expression can be applied in a wide range of notch depths and opening angles.     

Enhancement of Flexural Design of Horizontally Curved Prestressed Bridges

In this paper, flexural behavior of horizontally curved prestressed (posttensioned) box bridges is studied by using three-dimensional and refined finite-element modeling and analysis. Bridge length, section geometry, and material properties are the same in all the models, while angle of curvature varies from 0 to 90°. The results of analysis show that in curved bridges, stress distribution is significantly different in comparison to straight bridges. Also, the level of stresses at some locations of section width is considerably high. It is proposed to vary the distribution of the prestressing tendons across section width in order to optimize the bridge capacity. Results show that by proper redistribution of prestressing in section width, significant reduction in resultant stress is possible.     

Finite element analysis of a center crack specimen warm pre-stressed under different modes of loading

Load bearing capacity of cracked specimens can be improved following pre-loading procedures like warm pre-stressing (WPS). In this paper, the effects of modes I and II pre-loading on fracture load of a central angled crack specimen are studied by finite element analysis. The specimen is reloaded either in mode I or in mode II. To predict the fracture load of cracked specimen after pre-loading, the maximum tensile stress (MTS) and maximum shear stress (MSS) criteria are used. It is shown that mode II fracture load is independent of pre-loading but the mode I fracture load is highly improved after warm pre-stressing. The mode mixity of the specimen is also changed when the pre-loading and reloading modes are not identical. An increase in the fracture load of the specimen following pre-loading may be due to change of failure mode as predicted by finite element analysis in this work.     

Applications of the discrete element method in mechanical engineering

Compared to other fields of engineering, in mechanical engineering, the Discrete Element Method (DEM) is not yet a well known method. Nevertheless, there is a variety of simulation problems where the method has obvious advantages due to its meshless nature. For problems where several free bodies can collide and break after having been largely deformed, the DEM is the method of choice. Neighborhood search and collision detection between bodies as well as the separation of large solids into smaller particles are naturally incorporated in the method. The main DEM algorithm consists of a relatively simple loop that basically contains the three substeps contact detection, force computation and integration. However, there exists a large variety of different algorithms to choose the substeps to compose the optimal method for a given problem. In this contribution, we describe the dynamics of particle systems together with appropriate numerical integration schemes and give an overview over different types of particle interactions that can be composed to adapt the method to fit to a given simulation problem. Surface triangulations are used to model complicated, non-convex bodies in contact with particle systems. The capabilities of the method are finally demonstrated by means of application examples. Commemorative Contribution.     

稀土棕红色陶瓷颜料的制备

在低温下,采用溶胶均匀共沉淀法合成了含少量稀土氧化物CeO2的棕色陶瓷颜料,并应用颜色测定、SEM及XRD分析等手段对颜料的颜色、粒度及结晶构造进行了表征。同时,将合成的颜料应用于陶瓷釉料中,表明该颜料可以应用于1320℃的高温环境下。     

“菜鸟“小议

近年来,"菜鸟"作为一个新兴词语在网络上广为流传,甚至波及到社会生活的方方面面.通过语素分析和近义比较,可以来考察此词的读音和意义.     

Characterization of EBPVD micro-layer composites and simulation of its internal stress state

Based on the basic operating principal and the technology characteristic of electron beam physical vapor deposition(EBPVD) technique, EBPVD was used to prepare the micro-layer composites. The effect on the substrate preheating temperature was taken into accounts and the finite element analysis package ANSYS was used to simulate the internal stress field and the potential displacement changing tendency. The results show that one of the most important quality factors on the judgment of micro-layer composites is the adhesion between the substrate and the deposition layers as well as among the different deposition layers. Besides the existance of temperature gradient through the thickness of layers, the main reason for the internal stress in micro-layer composites is the mismatch of various properties of the layer and the substrate of different thermal expansions and crystal lattice types. With the increase of substrate preheating temperature, the inter-laminar shear stress also takes on a tendency of increase but the axial residual stress decrease.