Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

A review of the existing performance verification infrastructure for micro-CMMs

The performance verification of micro-CMMs is now of intense interest because of their capability to perform length measurements in three dimensions to high accuracy with low uncertainties. Currently, verification of micro-CMMs is completed in the spirit of existing specification standards, because strict adherence to these standards is often difficult. This review aims to present and discuss verification techniques available for micro-CMMs: specification standards, existing calibrated test lengths and traceability routes that can be associated with micro-CMMs. Three specification standards used in the testing of CMMs will be considered. In addition, a wide range of calibrated test lengths are reported, and any advantages and disadvantages associated with their use are discussed. It is concluded that micro-CMMs cannot yet be verified in accordance with existing specification standards. Suggestions are made for future standardisation work required to rectify these issues.     

无线电综合测试仪校准装置的研究及其不确定度分析

This calibration device of radio comprehensive tester is studied and established in this paper. It solves the verification and calibration of a large number of general-purpose radio comprehensive testers. The calibration device consists of four calibration sub- systems and calibration software system, including RF generator, audio generator, audio analyzer and RF analyzer. It also researches on the configuration of standard equipment and analyzes the uncertainty of the calibration devices, ensuring accurate and reliable val- ue transfer.     

An industrial case study on variability handling in large enterprise software systems

ContextEnterprise software systems (e.g., enterprise resource planning software) are often deployed in different contexts (e.g., different organizations or different business units or branches of one organization). However, even though organizations, business units or branches have the same or similar business goals, they may differ in how they achieve these goals. Thus, many enterprise software systems are subject to variability and adapted depending on the context in which they are used.ObjectiveOur goal is to provide a snapshot of variability in large scale enterprise software systems. We aim at understanding the types of variability that occur in large industrial enterprise software systems. Furthermore, we aim at identifying how variability is handled in such systems.MethodWe performed an exploratory case study in two large software organizations, involving two large enterprise software systems. Data were collected through interviews and document analysis. Data were analyzed following a grounded theory approach.ResultsWe identified seven types of variability (e.g., functionality, infrastructure) and eight mechanisms to handle variability (e.g., add-ons, code switches).ConclusionsWe provide generic types for classifying variability in enterprise software systems, and reusable mechanisms for handling such variability. Some variability types and handling mechanisms for enterprise software systems found in the real world extend existing concepts and theories. Others confirm findings from previous research literature on variability in software in general and are therefore not specific to enterprise software systems. Our findings also offer a theoretical foundation for describing variability handling in practice. Future work needs to provide more evaluations of the theoretical foundations, and refine variability handling mechanisms into more detailed practices.     

仙游抽水蓄能电站尾水系统充排水试验

为检查工程质量,查找输水系统可能存在的问题并消除隐患,保障电站安全运行,福建仙游抽水蓄能电站在投产发电前,要对输水发电系统进行充水试验与放空排水试验,在试验过程中监测输水系统的应力、应变与渗漏水情况。本文以尾水系统为例,介绍了试验所应具备的工程条件、工作程序及技术要求、试验成果分析和存在问题处理等。试验表明,仙游抽水蓄能电站尾水系统设计合理,施工质量优良,结构可靠,可供同类工程参考与借鉴。     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。