TiSiW12O40/TiO2催化合成丙酸正丙酯

研究了固载杂多酸盐TiSiW12O40/TiO2催化丙酸与正丙醇的酯化反应，探讨了催化剂用量，反应时间及醇酸摩尔比对酯收率的影响。当醇酸摩尔比为1.3:1，催化剂的量为醇酸总质量的1.5%。反应时间为1.0h，酯产率可达71.4%以上，采用该催化剂合成丙酸正丙酯不仅酯化反应温度低，反应时间较短，催化剂用量少，而且可较好地回收利用，可降低成本；因此，TiSiW12O40/TiO2是合成丙酸正丙酯的优良催化剂，具有良好的应用前景。     

源气体流量比对F-DLC薄膜结构的影响

以高纯石墨作靶，CHF3/Ar作源气体采用反应磁控溅射法制备出了氟化类金刚石（F-DLC）薄膜。拉曼光谱表明，CHF3相对流量的增加会引起薄膜的D峰与G峰强度之比I（D）/I（G）减小，晶粒增大，芳香环结构出例下降。红外吸收光谱分析证实了这些推论，指出这是由于薄膜中氟含量上升的结果。     

Preparation of Compound Ultrafine CeO2 by Wet-Solid-Phase Mechanochemical Modification

To satisfy practical requirements from industrial applications, an alternate route for synthesis compound ultrafine CeO2 powders by wet-solid-phase mechanochemical modification using industrial grade hydrated cerium carbonate as raw material was proposed.The effect of modifier reaction percentage, reaction time, calcining temperature and modifier amount on particle size, density, suspensibility, and hardness of compound CeO2 powder was investigated.The phase evolutions of preparation process were characterized by XRD.SEM micrograph of the final product shows that compound CeO2 powders obtained are well-dispersed, spherically-shaped, uniformly-sized and submicron-sized particles.The method is readily available in raw material, low in cost, simple in process, and has great potential for industrialization.The compound CeO2 powders of different physical properties can be synthesized by controlling the above-mentioned influence factors in preparation process.     

运用PLC技术改造385m~2凯利式叶滤机控制系统

根据生产实践 ,结合PLC的技术特点和 385m2 凯利式叶滤机的电气联锁特性 ,阐述了应用PLC技术 ,可进一步提高 385m2 凯利式叶滤机的运转率和自动化水平。     

Two Isomers of C60F48: Computed Inter-isomeric Equilibrium

C₆₀F₄₈ has been known to exist in two isomeric forms of D₃ and S₆ symmetries. However, the quantum-chemical calculations have not agreed on their stability order though a near-isoenergetic picture is otherwise always encountered. In order to clarify the situation, the entropy effects are evaluated for synthetic temperatures of about 500K. The entropy evaluations suggest that the D₃ isomer should be more stable in the potential energy by 2.05-2.55 kcal/mol (to which term the ab initio data are closer than the semiempirical ones).     

Synthesis of chemically and structurally modified dicalcium silicate

This paper describes the synthesis of cements, chemically and structurally related to Ca₂SiO₄. Silica was obtained from rice hull after heating at 600 °C. Calcium oxide and small amounts of barium chloride were mixed in order to obtain a final (Ca/Si) or (Ca+Ba)/Si ratio equal to 1.95, 1.90, and 1.80, which is lower than in the conventional cement. The solids were mixed and ultrasonically treated for 1 h with a water/solid ratio of about 20. After drying and grinding, the mixtures were heated up to 1100 °C. It was possible, in some cases, to obtain a cementitious material. These cements are structurally related to β-Ca₂SiO₄ and the lower (Ca+Ba)/Si ratio obtained was 1.95. The initial chemical compositions of these cements are: (Ca_1.83+Ba_0.12)SiO₄ and (Ca_1.79+Ba_0.16)SiO₄. A further lowering in the (Ca+Ba)/Si ratio changes the nature of the silicates.     

Microstructure and properties of MoSi2–MoB and MoSi2–Mo5Si3 molybdenum silicides

MoSi₂-based intermetallics containing different volume fractions of MoB or Mo₅Si₃ were fabricated by hot-pressing MoSi₂, MoB, and Mo₅Si₃ powders in vacuum. Both classes of alloys contained approximately 5 vol.% of dispersed silica phase. Additions of MoB or Mo₅Si₃ caused the average grain size to decrease. The decrease in the grain size was typically accompanied by an increase in flexure strength, a decrease in the room temperature fracture toughness, and a decrease in the hot strength (compressive creep strength) measured around 1200 °C, except when the Mo₅Si₃ effectively became the major phase. Oxidation measurements on the two classes of alloys were carried out in air. Both classes of alloys were protected from oxidation by an in-situ adherent scale that formed on exposure to high temperature. The scale, although not analyzed in detail, is commonly recognized in MoSi₂ containing materials as consisting mostly of SiO₂. The MoB containing materials showed an increase in the scale thickness and the cyclic oxidation rate at 1400 °C when compared with pure MoSi₂. However, in contrast with the pure MoSi₂ material, oxidation at 1400 °C began with a weight loss followed by a weight gain and the formation of the protective silica layer. The Mo₅Si₃ containing materials experienced substantial initial weight losses followed by regions of small weight changes. Overall, the MoB and Mo₅Si₃ additions to MoSi₂ tended to be detrimental for the mechanical and oxidative properties.     

A new family of ionic liquids based on the 1-alkyl-2-methyl pyrrolinium cation

Five new salts based on 1-alkyl-2-methyl pyrrolinium ion are reported, two involving the iodide ion and three involving the bis(trifluoromethanesulfonyl) amide ion. The iodide salts have melting points around 100 °C, while the amide salts have melting points around room temperature. Two of the amide salts can be easily quenched into the glassy state and exhibit glass transition temperatures around −70 °C. The 2-methyl pyrrolinium cation bears structural similarities to the aromatic imidazolium cations on one hand and the cyclic ammonium cation family based on the pyrrolidinium cation on the other. The properties of the salts reported here are compared within these two related families of salts.     

基于MPEG—2文件的合并

本介绍了具有相同音频、视频编码方式的MPEG2节目流如何合并成一个节目流。合并后的件播放流畅并且时间显示正确。它包括PAT PMT表的重写，系统头部分相关字段的更改，PCR值的修改，解码时间标签（DTS），显示时间标签（PTS）的重新确定，传送速率的修改以及添加相应的空包。     

New approach to environmentally benign epoxidation: the solid-phase-system using urea–H2O2 and recyclable dodecatungstate on apatite

On the basis of new concept using a solid disperse phase we have developed an efficient catalytic solid-phase-system for epoxidations of alkenes using urea–hydrogen peroxide (urea–H₂O₂) complex and cetylpyridinium dodecatungstate ((CetylPy)₁₀[H₂W₁₂O₄₂]) catalyst on fluorapatite (FAp). The recovered solid catalyst phase was reused to keep the catalytic activity after several times. In the conceptual idea it is a key point that in situ solid-phase-activation of the catalyst with urea–H₂O₂ proceeds to form microcrystals of the active species dispersed on the solid phase. The dispersion of the catalyst on FAp in the case of tungstic acid (H₂WO₄) was suggested by EPMA analysis. We proposed the peroxo type of species keeping the parent polyoxometalate framework as novel active species from FT-IR spectroscopic studies. FAp phase plays important roles of dispersing the active species on its surface to have high catalytic activity and of stabilizing the active species to lead to high reusability.