梳针刺辊与锯齿刺辊分梳差异的研究

为研究刺辊类型、速度对纤维损伤和去除结杂的影响,用Uster AFIS单纤维测试系统,分别对三种梳针刺辊和一种锯齿刺辊在二档道夫速度和四档刺辊速度条件下所加工的生条进行了检测.结果显示:梳针刺辊在减少纤维损伤方面明显优于锯齿刺辊;梳棉机产量低时,梳针剌辊去除棉结的效果好一些,梳棉机产量高时,锯齿刺辊去除棉结的效果要好于梳针剌辊;梳棉机产量低时,大都以锯齿和梳针Ⅲ刺辊去除杂质效果好些,梳棉机产量高时,锯齿和梳针Ⅱ刺辊去除杂质效果好些.     

自由空间二维榕树网实现方法

鉴于榕树网在自由空间光子交换网络中具有重要的应用价值,分析了榕树网的特点和4×4二维榕树网的空间拓扑结构,通过偏振光分光棱镜、微闪耀光栅阵列、平面反射镜、半反半透镜和液晶空间光调制器的集成,构建二维的榕树交换网实验模块,利用微闪耀光栅的衍射特性,控制每块微闪耀光栅的周期,以实现入射光信号不同方向的闪耀输出,最终完成二维榕树网自由空间水平和竖直方向上的交叉互连,直通则由平面镜反射实现。对二维榕树网实验模块的功能分析表明,该实验模块理论上可以完成4×4二维面阵内光信号(或数据)的排序、交换、组播、广播、矩阵变换等操作,具有交换透明、速度快、空间带宽高等特点,在全光交换和光通信中具有一定的应用。     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

矩形微带串馈线阵的设计和仿真

介绍了矩形微带贴片天线的特点、原理和设计方法,设计了3×1矩形贴片组成的串馈驻波线阵,运用以有限元法为原理的专业软件AnsoftHFSS对该天线进行仿真,并与测量结果进行比较,仿真结果与测量结果吻合。     

基于嵌入式计算机和Ethernet的分布式波控系统

介绍一种基于嵌入式计算机和以太网(Ethernet)的相控阵雷达分布式波控系统。整个波控系统以数个嵌入式计算机为核心，通过以太网与雷达的控制计算机通讯。     

准最佳二进阵列偶

本文在最佳二进阵列、准最佳二进阵列和最佳二进阵列偶的基础上,定义了一种新的最佳信号,即准最佳二进阵列偶.讨论了准最佳二进阵列偶的体积、变换性质,并对其进行了Fourier频谱分析,得到了部分有益的结果.还用计算机穷举搜索出了体积从2~24的准最佳二进阵列偶.     

自成像列阵共振腔的分析——Ⅰ.Talbot共振腔

利用自成像效应进行半导体列阵激光器锁相是一种重要的外腔锁相技术,所构成的共振腔可分为Talbot腔和带相位补偿板的Lau腔。我们用Fox-Li方法计算了共振模式。本文给出了Talbot腔的计算结果和分析,表明同相和反相模的损耗随腔长变化存在临界点。     

面阵列封装器件的贴装技术

面阵列封装器件在电子产品中的使用率逐年上升，如何实现其高速贴装是影响生产线效率的重要因素。从不同的角度论述了面阵列封装器件实现高速贴装的手段与技术。     

Service Load Effective Compression Flange Width in Fiber Reinforced Polymer Deck Systems Acting Compositely with Steel Stringers

This paper reports on the field study of a steel stringer-fiber reinforced polymer (FRP) deck composite bridge in Pennsylvania. The objective of the study is to assess the effective compression flange width in the FRP deck and floor systems when they act compositely with underlying steel girders at service conditions. The research results reported herein support the notion of employing a design approach, for both interior and exterior girders of a composite floor system, that is philosophically consistent with current practice related to steel girders acting compositely with concrete decking. It appears from the results presented herein that FRP decks and floors acting compositely with underlying steel girders exhibit an effective width that is close to the actual girder spacing for interior beams, and approximately one-half this value for exterior beams.