Micro- and nano-scale deformation behavior of nylon 66-based binary and ternary nanocomposites

The primary aim of this paper is to provide an insight on the effect of the location of organoclay on the micro- and nano-scale deformation processes in melt-compounded nylon 66/organoclay/SEBS-g-MA ternary nanocomposites prepared by different blending sequences. In addition, the deformation processes of the ternary nanocomposites were compared to the binary nanocomposites (nylon 66/organoclay and nylon 66/SEBS-g-MA) and neat nylon 66. The incorporation of SEBS-g-MA particles toughened nylon 66 markedly; but the flexural modulus and strength were both reduced. Conversely, the use of organoclay increased the modulus but decreased the fracture toughness of nylon 66. Nylon 66/SEBS-g-MA/organoclay ternary nanocomposites exhibited balanced elastic stiffness and toughness. Stress-whitening studies of the fracture surfaces in terms of gray level were also performed and an attempt was made to correlate the optical reflectivity characteristics with fracture toughness. It was concluded that the capability of SEBS-g-MA particles to cavitate was decreased by the presence of organoclay in the SEBS-g-MA phase, resulting in reduced toughening efficiency. The best micro-structure for toughness and other mechanical properties is thus to maximize the amount of exfoliated organoclay in the nylon 66 matrix rather than to have it embedded in the finely dispersed SEBS-g-MA particles.     

Machinability of Metal Matrix Composites Reinforced by 3-D Network Structure

Metal matrix composites reinforced by three-dimensional (3-D) continuous network structure reinforcement (3DCNRMMC) are difficult to machine due to serious tool wear and poor surface roughness caused by the brittle and hard reinforcement which interpenetrate into ductile matrix. In order to achieve the approach of low cost of 3DCNRMMC, the machinability of it needs to be understood. The influences of three cutting parameters and volume fraction of reinforcement on cutting force were analyzed in detail. The results indicate that: (1) Due to the brittle phase(s) introduced into ductile matrix of composites, there is a large fluctuation of cutting force causing deterioration of machinability. The fluctuation ranges of cutting forces, initially increase rapidly with the increase of volume fraction of reinforcement and then decrease finally, are largest at the range of the volume fraction of 55–65%; (2) The influence of cutting parameters on cutting force is obvious. With the increases of cutting speed, cutting force decreases gradually unless cutting speed exceeds the value of 209 m/min. Cutting forces increase with increasing feed rate and depth of cut; (3) Owing to the large fluctuation of cutting force, there were some cratered surfaces caused by Si₃N₄ reinforcement pulling-out and flaking-off. Some brittle phase protruding from the machined surface caused the deterioration of machined surface.     

谱映像定理在欧氏空间中的另类证明

以泛函分析中的谱映像定量为基础,利用矩阵可以约化为若当型的特点,用一种非常简便的方法证明了欧氏空间中的谱映像定理,给出了一类矩阵指数特征值与原矩阵特征值之间的关系,并给出具体的实例验证结果的有效性.     

一次同余方程组的一种矩阵解法

同余方程组是数论中一个极为有用的课题。文中考虑的是具有一个未知数而具有不同的模的一次同余方程组。一般可以用中国剩余定理或者递推算法等方法给出一次同余方程组的解法。利用矩阵的初等变换和矩阵的Sm ith标准形给出了求解一次同余方程组的一种矩阵解法。     

Second-Order Stiffness Matrix and Loading Vector of a Beam-Column with Semirigid Connections on an Elastic Foundation

The second-order stiffness matrix and corresponding loading vector of a prismatic beam–column subjected to a constant axial load and supported on a uniformly distributed elastic foundation (Winkler type) along its span with its ends connected to elastic supports are derived in a classical manner. The stiffness coefficients are expressed in terms of the ballast coefficient of the elastic foundation, applied axial load, support conditions, bending, and shear deformations. These individual parameters may be dropped when the appropriate effect is not considered; therefore, the proposed model captures all the different models of beams and beam–columns including those based on the theories of Bernoulli–Euler, Timoshenko, Rayleigh, and bending and shear.The expressions developed for the load vector are also general for any type or combinations of transverse loads including concentrated and partially nonuniform distributed loads. In addition, the transfer equations necessary to determine the transverse deflections, rotations, shear, and bending moments along the member are also developed and presented.     

基于判断矩阵的软件评价指标权重分配方法

本文主要讨论判断矩阵的性质和特点，阐明了利用判断矩阵为软件质量评价指标分配权重的原理，对一致性较差的判断矩阵给出了修正方法，最后给出了权重分配方法。     

Combined Petri net modelling and AI-based heuristic hybrid search for flexible manufacturing systems—part II. Heuristic hybrid search

This two-part paper presents modelling and scheduling approaches of flexible manufacturing systems using Petri nets (PNs) and artificial intelligence (AI)-based heuristic search methods. In Part I, PN-based modelling approaches and basic AI-based heuristic search algorithms were presented. In Part II, a new heuristic function that exploits PN information is proposed. Heuristic information obtained from the PN model is used to dramatically reduce the search space. This heuristic is derived from a new concept, the resource cost reachability matrix, which builds on the properties of B-nets proposed in Part I. Two hybrid search algorithms, (1) an approach to model dispatching rules using analysis information provided by the PN simulation and (2) an approach of the modified stage-search algorithm, are proposed to reduce the complexity of large systems. A random problem generator is developed to test the proposed methods. The experimental results show promising results.     

化学结构的计算机处理（Ⅱ）：化学结构的计算机内存储方式和文件格式

化学结构作为化学家最普遍使用的语言，在化学知识的记录，传播和交流中起着十分重要的作用。随着计算机的普及，广大化学工作者都希望能用计算机来帮助处理化学结构，本文介绍了目前面向计算机的化学描述方法中用得最多的几种存储方式和文件格式，它们是：邻接矩阵，邻接表，邻接多表和ＭＯＬ格式，ＳＭＤ格式，简要评述了这些存储方式和文件格式的特点，局限性的应用。     

连续转子式电池生产线的技术实现

本文从机械原理分析了间隙式和连续式生产的差别，显示电池连续生产的重大意义，并且对如何实现连续转子式电池生产线作了深入的讨论。