High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

水泥窑余热发电系统用耐磨材料的研制与应用

本研究针对水泥窑余热发电系统的工作条件,根据耐磨材料的损毁机理,采用高铝矾土、煅烧氧化铝粉、黏土、硅微粉等为原料,以磷酸二氢铝为结合剂,以铝酸钙水泥为促硬剂,通过添加掩蔽剂和优化配料工艺,制备了水泥窑余热发电系统用耐磨材料,并对不同处理温度对耐磨材料的性能影响进行了分析。结果表明增强骨料与基质的结合能力有利于耐磨性的提高,磷酸及磷酸盐与氧化铝之间会随着温度的升高生成不同的磷酸铝相,都能够起到结合作用,比采用水泥结合更有利于提高材料在不同温度下的强度和耐磨性。使用结果表明,制备的耐磨材料施工性能优良,凝结硬化时间适当,强度高,抗冲刷性能好,在水泥窑余热发电系统中取得了良好的使用效果。     

Synthesis and Characterization of Co Nanocomposite Based on Poly(benzimidazole-amide) Matrix and Their Behavior as Catalyst in Oxidation Reaction

2,6-Bis(5-amino-1H-benzimidazol-2-yl)pyridine was prepared and characterized by Fourier transform infrared spectroscopy, elemental analysis, ¹H-NMR, and ¹³C-NMR spectroscopic methods. Then a new poly(benzimidazole-amide) was synthesized by polymerization of the corresponding diamine and isophthalic acid. The obtained poly(benzimidazole-amide) exhibited good yield and high thermal stability. Due to the existence of benzimidazole moieties in polymer’s structure, it has the tendency to form complexes with metal ions. So, a new poly(benzimidazole-amide)/Co nanocomposite was prepared. Morphological studies revealed that metal nanoparticles were dispersed in the polymer matrix without any aggregation. poly(benzimidazole-amide)/Co nanocomposite was used as a catalyst in the oxidation of ethyl benzene to acetophenone with tert-butyl hydroperoxide.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Nonlinear dynamic behaviors and control based on simulation of high-purity heat integrated air separation column

In this paper, the dynamic behaviors on the basis of simulation for high-purity heat integrated air separation column (HIASC) are studied. A nonlinear generic model control (GMC) scheme is proposed based on the nonlinear behavior analyses of a HIASC process, and an adaptive generic model control (AGMC) scheme is further presented to correct the model parameters online. Related internal model control (IMC) scheme and multi-loop PID (M-PID) scheme are also developed as the comparative base. The comparative researches are carried out among these linear and nonlinear control schemes in detail. The simulation research results show that the proposed AGMC schemes present advantages in both servo control and regulatory control for the high-purity HIASC.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

基于WiMAX通信网络的电源监控系统的构建

分析了全球微波接入互存(WiMAX)的技术特点和算法复杂度,探讨了其在电源监控系统中的应用,提出了基于Inter WiMAX Connection 2250技术的远程电源监控系统。在讨论WiMAX物理层算法的基础上,确定了以正交频分多址(OFDMA)模式为主体的物理层通信协议,提高了信道的利用率,抑制了码间干扰,为构建电源监控系统打下了良好的基础。     

Optimal siting and sizing of demand response in a transmission constrained system with high wind penetration

This paper describes algorithms that use demand-side management to address large-scale integration of wind power. In particular, demand response (DR) is used to manage wind power intermittency by shifting the time that electrical power system loads occur in response to real-time prices and wind availability. An economic dispatch with transmission, DR capacity and operational constraints is used to model the operation of a transmission constrained system with a high penetration of wind power. This optimization model is used to determine the optimal sizing and distribution of DR given a fixed budget for customer incentives and the installation of enabling technology. We demonstrate the effectiveness of the operational model based on a simple PJM 5-bus system and an IEEE 118-bus system. Simulation results show that transmission constraints have a greater effect on sizing of DR capacity than the location of wind power, which means that buses electrically close to congested lines tend to have higher incentives to deploy DR resources than other buses. The second part of the work examines optimal siting of technology that enables DR based on the frequency of DR based load changes, which are generally a function of the network location.     

Dynamic probe of ZnTe(110) surface by scanning tunneling microscopy

The reconstructed surface structure of the II–VI semiconductor ZnTe (110), which is a promising material in the research field of semiconductor spintronics, was studied by scanning tunneling microscopy/spectroscopy (STM/STS). First, the surface states formed by reconstruction by the charge transfer of dangling bond electrons from cationic Zn to anionic Te atoms, which are similar to those of IV and III–V semiconductors, were confirmed in real space. Secondly, oscillation in tunneling current between binary states, which is considered to reflect a conformational change in the topmost Zn–Te structure between the reconstructed and bulk-like ideal structures, was directly observed by STM. Third, using the technique of charge injection, a surface atomic structure was successfully fabricated, suggesting the possibility of atomic-scale manipulation of this widely applicable surface of ZnTe.     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.