Stress relaxation behavior of Ti-6Al-4V alloy

1　INTRODUCTIONTi 6Al 4VisoneofthemostimportantTial loys[1,2 ] .Butthisalloyhasbadformabilityforitshighelasticresilience .Therefore ,hotsizingisimpor tant[36 ] .Asthebaseofhotsizing ,thestudyofstressrelaxationhasimportanttheoreticalvalueandpracticalsignificance .Ontheotherhand ,Ti 6Al 4Visusedasfastenermaterialssometimes .Whenthefastenersworkatthetemperaturehigherthanroomtemperature ,stressrelaxationmayresultsinacci dents .Sohowtopreventthestressrelaxationisveryimportant[7] .Uptonow ,…     

钛合金中亚晶的电子显微镜观察

用透射电子显微镜观察了TC6钛合金在高温退火过程中形成的亚晶(Subgrain)。合金经850℃,920℃退火后炉冷和空冷,在初生α相晶粒内形成亚晶,多为成簇分布的狭长形状,亚晶的数量随退火后冷却速度的增加而减少。亚晶界(Subgrain boundary)是由位错构成的,亚晶的形成是多边化(polygonization)的结果。     

Al-K2ZrF6体系熔体反应法合成复合材料的微观组织和力学性能

开发了Al-K2ZrF6体系熔体反应法合成原位铝基复合材料，采用XRD，SEM和TEM分析了复合材料中相组成、微观组织和界面结构。实验结果表明：合成的增强相为Al3Zr颗粒，常规金属型铸造的复合材料中其尺寸在3μm～4μm左右，一般成聚集态分布，颗粒形貌基本为长方体状：该复合材料经重熔快淬成形后，颗粒尺寸减小，基本为粒状，并弥散分布于基体上。Al3Zr／Al复合材料的界面结构研究表明，Al3Zr颗粒与Al存在一定的晶体学位向关系：[^-2^-21]Al3Zr∥[100]Al，（012）Al3Zr∥（1^-10）Al，其点阵错位度仅为10．87％，这表明Al3Zr颗粒可作为基体Al相的形核衬底。Al3Zr／Al复合材料的力学性能测试显示，当Al3Zr颗粒体积分数为11.2％时，抗拉强度和屈服强度分别为148．7MPa和110．2MPa，而且Al3Zr／Al复合材料的抗拉强度和屈服强度均随颗粒体积分数增加显著提高。     

Study On the Tribological Behavior of the Arc-added Glow Discharge Plasma Non-hydrogen Carburization On Titanium Alloy Surfaces

This paper introduces a new titanium alloys surface strengthening treatment by using the arc-added glow discharge plasmas non-hydrogen carburization technique. High purity and high strength graphite is selected as cooling cathode arc source for supplying carbon atoms and particle, which migrate to the titanium alloy(Ti6Al4V) surface and form modified layer. Thus, the hydrogen embrittlement is avoided while the tfibological behavior of the titanium alloy surface is improved in the respects of anti-friction and anti-wear ability.The tribological behavior of the modified layer under dry sliding against SAE52100 steel was evaluated on a ball-on-disc test rig. The results showed that the modified layer obtained a thickness of 30μm at 980℃, 30minutes. The microhardness of the Ti6Al4V alloy surface attained 936 HV, which was much larger than that of the Ti6AI4V alloy. The Ti6AI4V alloy was characterized by adhesion wear and scuffing under dry sliding against the steel, while the surface modified layer experienced much abated adhesion wear and scuffing under the same testing condition. This could be attributed to the carbon dement with different modalities exists in the modified layer.The modified layer showed good friction-reducing and fair anti-wear ability in dry sliding against the steel. Using the SEM,XRD and XPS, the phase structure and morphology of the carburization modified layer was analyzed.     

锡磷青铜合金水平连铸工艺参数的优化

铸造锡磷青铜合金组织中存在显微缩松、枝晶偏析和反偏析是冷加工报废的主要原因.通过连铸工艺参数的正交实验,建立了轧制成材率与主要工艺参数之间的神经网络描述,网络模型与遗传算法结合对工艺参数的组合进行了优化,改善了铸坯的组织,提高了轧制带材成材率.     

Effect of cold spray deposition of a titanium coating on fatigue behavior of a titanium alloy

The deposition of titanium on a titanium alloy substrate is being examined for potential use as a surface treatment for medical prostheses. A Ti6Al4V alloy was coated with pure titanium by cold gas dynamic spraying. Coatings were deposited onto samples with two different surface preparation methods (as-received and grit-blasted). The fatigue life of the as-received and grit-blasted materials, both before and after coating, was measured with a rotating-bend fatigue rig. A 15% reduction in fatigue endurance limit was observed after application of the coating to the as-received substrate, but no significant reduction was observed on its application to the grit-blasted substrate. The reduction in fatigue endurance limit has been related to the substrate-coating interface properties, the elastic modulus, and the residual stress states. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference, (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, 2006.     

2,4,6-三硝基苯甲酸的合成工艺改进

对TNT(2，4，6-三硝基甲苯)氧化制备2，4，6-三硝基苯甲酸的工艺进行了深入的研究，结果表明氧化剂的种类、用量、加料方式及溶剂的种类对产物的收率有较大影响。TNT的较佳氧化工艺条件为：氧化20gTNT，以摩尔比为4：1的HNO3和HCI混合液作为溶剂，采用液体加料方式加入氧化剂KClO4 40g，2，4，6-三硝基苯甲酸的收率最高达96％。     

国产纺丝机与引进分丝设备配套的分丝工艺研究

通过对国产VC406纺丝机与引进DW-200无捻拉伸机、MC16分丝络筒机等设备的配套和分丝生产工艺的研究,着重论述采用分丝路线生产锦纶高支单丝的纺丝、分丝工艺和该路线生产单丝的特点以及各工序对前道的要求。该配套生产线经一年多时间的正常运行,产品质量已达到国际同类产品的水平。证明有关纺丝设备的改造是成功的,工艺是可行的。     

异丁醛合成2,4,6-三异丙基-1,3,5-三噁烷的研究

本文以异丁醛为原料在杂多酸催化剂的作用下，环化合成了无毒升华剂2，4，6－三异丙基－1，3，5－三恶烷，考查了各种反应条件的影响，确定以磷钨酸为催化剂时的最佳反应条件：反应温度25℃，催化剂用量1．5％，反应时间2．5h，产物的收率达84％以上。