神经网络在缺陷识别中的应用

为了准确、快速地进行缺陷识别，介绍了一种新型的前馈神经网络模型，即径向基概率神经网络。与以往的算法相比，该方法具有分类识别精度高且速度快的优点。仿真获得了很好的结果。     

清涧河流域不同水土保持措施配置下蓄水拦沙效益分析

从分析清涧河流域不同年代水土保持措施配置人手，以蓄水拦沙效益为研究目标，探讨了水土保持措施优化配置问题。分析认为：水土保持措施配置与蓄水拦沙效益是密切相关的，淤地坝在水土保持措施配置中应占有合理比重，坡面治理措施配置中需进一步加大封禁治理比例。     

黄河下游河道萎缩致灾机理探讨

本文基于水力学原理，结合实体模型试验及原型实测资料分析，探讨了黄河下游河道萎缩的概念、致灾效应和致灾机理。分析表明，河道萎缩是造床过程中河道排洪输沙功能衰退的一种演变现象，其致灾效应是使洪水涨率增大，同流量下洪水水位不断抬升。致灾的现象主要表现在畸型河势增加、工程险情增多、直接造成工程损失及滩区经济损失等。试验研究揭示，主河槽宽度缩窄造成洪水水位涨幅增大，河底平均高程抬升和过水断面面积减小造成洪水水位起涨的基准面抬升是河道萎缩致灾的主要原因。河道萎缩致灾效应的大小与萎缩模式有关，其中以“集中淤槽”模式所形成的致灾效应尤为明显。     

Nanostructured polymer blends: Synthesis and structure

Nanostructured polymer blends prepared via anionic ring opening polymerizations of cyclic monomers in the presence of a pre-made polymer melt exhibit a number of special properties over traditional polymer blends and homopolymers. Here, we report on a simple and versatile method of in situ polymerization of macrocyclic carbonates in the presence of a maleic anhydride polypropylene (mPP) matrix and a surface-active compatibilizer (i.e. PC grafted onto a mPP backbone generated in situ) to yield a micro- and nanostructured polymer blends consisting of a polycarbonate (PC) minor phase, and a polypropylene (PP) major phase. By varying the processing conditions and concentration of the macrocyclic carbonate it was possible to reduce the size of the PC dispersions to an average minor diameter of 150 nm. NMR and TEM characterizations indicate that the PC dispersions do not influence crystal content in the PP phase. Overall, the results point to a simple strategy and versatile route to new polymeric materials with enhanced benefits.     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

Identification of photoluminescence features of an epoxy resin based on components features and curing effects

Photoluminescence features in a commercial grade cured DGEBA-based epoxy resin have been investigated with as objective to determine which of the material compounds are responsible for cured resin emissions. The origin of the bands has been approached by considering photoluminescence of base resin and hardener taken separately, of their mixture, and in the course of curing. Most of the bands observed in the cured resin could be interpreted based on those found in the components taken separately. Fluorescence of the cured resin appears dominated by two broad bands that are characteristic of the hardener and exhibits a blue shift by up to 30 nm in the course of curing which could be used for cure monitoring purpose of the investigated system. Fluorescence of the base resin is clearly detected in the resin cured with tertiary amine as catalyser. However, it is very weak if the catalyser is not added. Two phosphorescence processes have been isolated in the cured resin, one of them being related to the base resin. Finally, a chemiluminescence spectrum has been recorded in the course of curing, which has been related to either curing-related reactions or to an oxidation process.     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.     

On the learning control of a robot manipulator

This paper derives a learning control law to achieve trajectory following for a robot manipulator. The controller consists of two parts, a computed torque servo for the rigid body terms that can be modelled and a learning law for the unmodelled dynamics. An advantage of this method is that bounds can be assigned to the position and velocity tracking errors.     

Generalized difference control of parallel streams temperatures

A furnace with multiple parallel passes and multiple burners is commonly seen in petroleum refineries. In order to maintain the furnace running in a safe, stable, and high-efficiency state it is necessary to control the outlet temperatures of the multiple passes to be the same. Due to the fact that the process of the oil heating in such furnace is nonlinear, multivariable, time varying, has serious coupling among passes, has frequent dynamic changes and a large time delay, traditional control methods have trouble in controlling these temperatures, and some advanced control methods, including predictive control, adaptive control, and robust control, are usually too complex for convenient use. In this paper, a control technique, called differences control technique (DsCT), is proposed to distribute the stream flowrates such that the stream temperatures are as identical as possible. The principle of the proposed technique is explained and demonstrated, and the results of its application to a real-life petroleum refinery furnace are also reported. The DsCT technique has the following advantages: it does not need complicated design procedures, the controller structure is simple, it is easy to apply, and it can be canonically applied to furnaces with different number of passes.     

工程施工阶段监理的投资控制

建设工程施工阶段是工程投资发生的主要阶段,监理工程师在该阶段应重点把好工程计量关、支付签证关及变更索赔关,从而实现对施工阶段投资的有效控制。