武山铜矿主井系统延深改造及效果浅析

武山铜矿主井延深时根据新的采、选工艺要求，在前期工程的基础上，对其箕斗提升系统进行改造，增设坑内破碎。针对该矿特粘的矿石性质和前期工程遗留问题，在具体设计和实施过程中采取特别措施保证系统通畅和安全并注意节省投资。同时对尚存在的问题也提出了新的思考。     

钻井液用BDY-1便携式堵漏仪

在堵漏过程中，对堵漏材料和堵漏浆配方的优选是决定堵漏成功的关键。为了能在现场对堵漏进行评价，研制出BDY－1便携式堵漏仪，该堵漏仪主要由不锈钢钢柱圈钢，压力表等加工而成，该堵漏仪体积小，重量轻，价格低，仅为国产堵漏仪的1／20。试验结果表明BDY－1便携式堵漏仪操作简便，可快速对堵漏材料进行评价并筛选出堵漏配方；数据重复性好，准确可靠，能达到进口或国产堵漏仪的水平；在模拟漏层选定后，可采用多套压力梯度，对堵漏浆封堵效果进行评价，在压力梯度选定后，可评价堵漏浆对不同类型漏层的封堵效果；如果扩大压力范围，可对封堵后的漏层进行破裂试验，从而确定合理的钻井施工参数；适用现场操作和应用。     

提高集聚纺纱效率的可行性研究

本文主要讨论了精梳工序和普梳工序对集聚纺纱线质量和加工效率影响的测试结果。     

枪械振动测试用光电六维位移传感器的设计

枪械振动测试包含刚体线位移和角位移六维运动参数.其测试方法是,将光电传感器光源与被测体固结在一起,通过求解光源在三个投影屏上随着被测体运动变化的数学模型而实现的.该传感器由激光器、投影屏、光电探测器件及处理电路、数据采集、数据处理等部分组成.并以固结在被测体上的三个激光器的交点为基点,建立其线位移数学模型;以方向余弦法来确定被测体的角位移,建立其角位移数学模型.     

CMS/TiO2杂化材料电流变液的制备及其性能

利用特殊的溶胶凝胶方法原位制备了改性淀粉与无机钛氧化物杂化型电流变材料。实验表明,在强电场下其电流变效应比相同组份的淀粉、二氧化钛混合型电流变液有显著提高,直流电场4 kV/mm,剪切速率5 s-1时,静态剪切屈服强度可达4000 Pa以上。同时,抗沉降性明显改善,静置100 h几乎不沉淀。此外,温度效应也获得一定的优化,在10 ℃~90 ℃的工作温度范围内力学性能保持良好,70 ℃时剪切强度达到最大值。     

Intermetallic compounds formed at the interface between liquid indium and copper substrates

The interfacial reactions between liquid In and Cu substrates at temperatures ranging from 175°C to 400°C are investigated for the applications in bonding recycled sputtering targets to their backing plates. Experimental results show that a scallop-shaped Cu₁₆In₉ intermetallic compound is found at the Cu/In interface after solder reactions at temperatures above 300°C. A double-layer structure of intermetallic compounds containing scallop-shaped Cu₁₁In₉ and continuous CuIn is observed after the Cu/In interfacial reaction at temperatures below 300°C. The growth of all these intermetallic compounds follows the parabolic law, which implies that the growth is diffusion-controlled. The activation energies for the growth of Cu₁₆In₉, Cu₁₁In₉, and CuIn intermetallic compounds calculated from the Arrhenius plot of growth reaction constants are 59.5, 16.9, and 23.5 kJ/mole, respectively.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

标准物质在分析测试中的重要地位及发展前景

标准物质在分析测试领域中无论在定值，方法的研究，误差确定等方面都有着重要地位。标准物质的质量保证及正确使用也应引起我们重视。随着科学技术迅速发展标准物质有着广阔发展前景。     

碳素材料超声检测的信号处理方法

针对碳素材料超声无损检测存在信噪比较低的问题,从自相关性出发分析了典型超声检测信号的组成成分,提出了在自相关分析的基础上的小波去噪思想,探讨了自相关分析和小波分析相结合的信号处理方法。利用此方法进行实际超声信号分析效果良好。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.