Modeling of Intercritical Heat Treatment of DP and TRIP Steels

The final microstructure of DP and TRIP assisted steels can evolve after hot working (hot rolling) or during post heat treatment process. In the formation of the final structure a number of different technological parameters have important roles, e.g. end temperature of rolling, cooling rates, temperature of intercritical annealing, etc. As a result of the individual factors and their combinations a lot of product technology routes are feasible. The effect of the different combinations of these technological parameters on the microstructure can be mapped by the special Jominy end-quench test (so called intercritical Jominy end-quench test) described in this paper. Unlike the traditional Jominy test, in this case there is a partial anstenizing between A1 and A3 temperatures which results in a given amount of ferrite in the microstructure before quenching. The method developed can be applied for mapping DP and TRIP assisted steels' microstructure in a wide range of technological parameters. The analysis of measured and calculated data can help us find the technological parameters optimal from the microstructural point of view.     

关于复杂黄铜的等效方法及其它

在复杂黄铜等效变换的多元变化过程中，存在着第三种当量系数Ｉ。它是确保合金转化为二元形式所必不可少的导向给定值，是一个定位常数。找出了Ｋ＋Ｊ＝０的误解的产生原因，论证了Ｋ＋Ｊ＝１所在达的过程的实质。指出用二元相图理解等效变换这一三元变化过程的认识误区。     

压痕法测定热压MoSi2基复合材料K1C值的研究

用不同的压痕方程计算了纳米ＺｒＯ２粒子韧化ＭｏＳｉ２基复合材料的室温断裂韧性Ｋ１ｃ值，同时研究了压痕载荷对Ｋ１ｃ值的影响。结果表明，试验材料在试验条件下的断裂韧性不遵从半月状裂纹系统方程，而遵从巴氏裂纹系统方程，其室温压痕断裂韧性保持与压痕载荷的独立性。     

催化动力学光度法在贵金属测定中的实际应用

综述了催化动力学光度法在钌、铑、钯、银、锇、铱、铂等贵金属测定中的实际应用新近发展状况。     

B 炸药中绝热剪切带形成机理的细观研究

通过对快速加载后Ｃｏｍｐ．药柱剖面的扫描电镜和光学显微镜观察分析，对Ｃｏｍｐ．Ｂ炸药在快速加载下剪切带形成机理的微观机制有了初步的认识。文中采用形变试样的剖面观察分析方法，针对固体药柱这种比较软的材料，如何进行磨样、抛光、浸蚀，作了一些尝试和探索，总结出一套有效的实施办法。对不同加载速率条件下受压缩的药柱中细观组织进行了观察、分析、比较，首次给出国产Ｃｏｍｐ．Ｂ炸药装药的原始细观组织形貌，以及快速加载后药柱中细观组织形貌。经过分析，得到冲击载荷下炸药装药中绝热剪切带形成、发展的定性认识，为分析Ｃｏｍｐ．Ｂ炸药装药受冲击载荷时热点形成机理提供了一些有益的实验依据。     

热塑性淀粉加工过程的控制参数及塑化程度的表征方法

在介绍热塑性淀粉塑料加工原理的基础上,提出特殊机械能可以作为描述热塑性淀粉塑化过程的控制参数;并对表征热塑性淀粉塑化程度的各种方法进行了总结和评述。     

配料系统中核子秤的实物标定法

针对使用单位对核子秤实物标定方法的认识与掌握不够，而导致核子秤不能正常使用的问题，文中详细介绍了配料系统中应用核子秤进行实物标定的条件及几种方法。     

Use of cascade reduction potential for selective precipitation of Au,Cu, and Pb in hydrochloric acid solution

Optimization of reduction potential for electroseparation was studied for the recovery of gold, copper, and lead from acidic solution. A linear sweep voltammetric method enabled us to determine characteristic reduction potentials for each metal and the kinetics of the metal deposition indicated by current-voltage curves. In order to precipitate the metal species sequentially, reduction potentials were examined for the individual and mixed solutions of Au(III), Cu(II), and Pb(II). The three metals were reasonably well isolated from the mixed solutions such as Cu(II)/ Pb(II) and Au(III)/Cu(II)/Pb(II) in the order of the corresponding reduction potentials, in particular, the mass transfer controlled reduction potentials, obtained from linear sweep voltammetry (LSV) measurement.     

双甲脒分析方法的国际协作研究

结合参加双甲脒分析方法的国际协作研究，对国际分析方法协作研究的一般程序做了介绍，反映了国际同行们的分析水平。对国内同行了解和掌握国际协作研究的程序，及国内分析方法标准的协作实验验证也有所裨益。     

Thermoelectric hydrogen sensor using Li x Ni1-x O synthesized by molten salt method

Li-doped NiO was synthesized by molten salt method. LiN_O3-LiOH flux was used as a source for Li doping. NiCl₂ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5: 1 to 30: 1 during the synthetic procedure and the chemical compositions after characterization were found from Li_0.08Ni_0.92O to Li_0.16Ni_0.84O. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies; however, the lattice parameter decreased from 0.41769 nm in pure NiO to 0.41271 nm in Li_0.16Ni_0.84O. Hydrogen gas sensors were fabricated by using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor, when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving the rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs H₂ concentration was checked up to 4% of H₂ in air (as higher concentrations above 4.65% are explosive in air) using Li_0.10Ni_0.90O as the sensor material. The response time T₉₀ and the recovery time RT90 were less than 25 sec. H₂ concentration from 0.5% to 4% showed a good linearity against voltage. There was minimum interference of other gases and hence H₂ gas can easily be detected.