Behavior of laser welded steel in chloride solution studied using difference imaging

In situ imaging techniques in conjunction with electrochemical measurements were used to study the behavior of steel surfaces in simple chloride solutions. The imaging method detected the presence of significantly thicker uniform layers than the original passive oxide. The layers were found to form in chloride after the steel was anodically polarized following reduction of the passive oxide film. The growth of the layer depended on the degree of prior passive oxide reduction. Formation of the layer was also sensitive to underlying structure and enabled rapid location of regions of higher corrosion rate across laser welds in steels.     

旋风管内气相的湍流运动特性

利用二维激光多普勒测速仪(LDV)测量了旋风管内湍流运动的时均速度、脉动速度、能谱函数、微分尺度及湍流耗散等参数，对湍流特性参数分布进行了详细的描述，并初步分析了旋风管内湍流运动特性对颗粒分离的影响.     

Well-dispersed single-walled carbon nanotube/polyaniline composite films

Single-walled carbon nanotube (SWNT)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dissolved SWNTs. The results of atomic force microscopy (AFM) and UV-Vis adsorption spectroscopy show that aniline can be used to solubilize SWNTs via formation of donor-acceptor complexes. The electrochemical deposition of SWNT-aniline solutions have been investigated by cyclic voltammetry. The results show that SWNT-based aniline solutions exhibit a drastic increase in peak current within the potential scanning region. The doping effect of SWNTs on PANI films was investigated by electrochemistry and FTIR spectroscopy. The results indicate that the enhanced electroactivity and conductivity of the SWNT/PANI composite films may be due to the strong interaction between SWNTs and PANI, which facilitates the effective degree of electron delocalization.     

抄数系统在产品设计和模具制造中的应用

介绍高速抄数机的基本结构、功能、工作流程以及在新产品开发,模具型腔、型芯设计和制造中的具体应用.     

塑料激光成型新技术

研究和探讨了塑料激光塑性成型的成型机理、变形方向控制。阐述了该成型方法的特点、影响因素及材料特性。并介绍了成型实例。     

Carbon membranes from cellulose and metal loaded cellulose

The focus of this work was to find a low-cost precursor for carbon molecular sieve (CMS) membranes, and a simple way of producing them. In addition, several ways of modifying a carbon material are described. The modification method used in this study was metal doping of carbon. CMS membranes were formed by vacuum carbonization of cellulose and metal loaded cellulose. Metal additives include oxides of Ca, Mg, Fe(III) and Si, and nitrates of Ag, Cu and Fe(III).The carbon membrane containing Fe-nitrate has promising separation performance for the gas pairs O₂/N₂ and CO₂/CH₄. Carbon containing nitrates of Cu or Ag show high selectivity, but reduced O₂ and CO₂ permeability compared to carbon with Fe-nitrate. Element analysis indicates that Cu migrates to the carbon surface, creating an extra layer resistance to gas transport. A silver mirror is also seen on the surface of Ag-nitrate-containing carbon. However, the Ag- and Cu-containing membranes show a high H₂ permeability. Adding metal oxides makes the carbon membranes retard the transport of easily condensable gases (e.g. CO₂). This can be exploited for enhanced H₂/CO₂ separation efficiency.     

Interfacial shear strength of C/C composites

Fiber-bundle push-out, single-fiber push-in, and single-fiber push-out tests were conducted in order to examine the applicability of these methods for determining the interfacial shear strength of carbon-carbon composites. The fiber-bundle push-out test resulted mostly in fractures along the fiber/matrix interface but created a small amount of fractures in the matrix. Hence, the evaluated strength was regarded as an approximate value. In order to precisely evaluate the interfacial strength, push-in and push-out tests for a single fiber were performed using a micro-Vickers indentation tester. In these tests, the load has to be placed within a target fiber, and the indentation should not extend to the matrix. This condition restricted the load that could be applied to a carbon fiber. Within this limit, a single carbon fiber could not be pushed-in. For the sake of load reduction, single-fiber push-out tests were conducted using thin specimens. The thickness appropriate for a single-fiber push-out specimen was estimated based on the interfacial shear strength obtained by the bundle push-out tests. Below this thickness, single-fiber push-out tests could be successfully performed.     

The effect of feedstock and process conditions on the synthesis of high purity CNTs from aromatic hydrocarbons

High purity multi-walled carbon nanotubes were synthesized from aromatic hydrocarbons (benzene, toluene, xylene and trimethyl benzene) using ferrocene as the source of Fe catalyst. Screening studies of aromatic feeds at 675 °C, residence time of 14 s and Fe/C atom ratio of 1.07%, resulted in feedstock carbon conversion of 20-31%, CNT yield of 19.8-30.5%, and catalyst yield of 5.3-8.3 (g CNT/g catalyst). While the quality of the CNTs as determined by TGA, SEM, TEM and Raman spectroscopy, were high and comparable for different feedstocks; their carbon conversion, CNT yield and catalyst yield differed noticeably. A process optimization study for toluene feed showed that carbon conversion of more than 39%, CNT yield of 38.7% and catalyst yield of 18.3 can be achieved at temperature of 800 °C, Fe/C atom ratio of 0.47%, and residence time of 10-20 s.     

Development of three-electrode type micro-electrochemical reactor on anodized aluminum with photon rupture and electrochemistry

Photon rupture with a focused single pulse of pulsed YAG-laser irradiation was used to fabricate an aluminum electrochemical micro-reactor. Porous type anodic oxide film formed on aluminum specimens was irradiated in solutions with a pulsed Nd-YAG laser beam through a convex lens to fabricate micro-channels, micro-electrode, and through holes (for reference electrode, solution inlet, and outlet). During irradiation, specimens were moved by a computer controlled XYZ stage. After irradiation, the surface of the micro-channel and through hole were again treated to form anodic oxide film and the surface of the micro-electrode was treated electrochemically to provide an Au layer. The calculated volume of the micro-reactor including micro-channel and through holes is about 1.5 μl. The cyclic voltammogram of the micro-electrochemical cell was measured in K₃Fe(CN)₆/K₄Fe(CN)₆ with both static and flowing solution at different scanning rates. The anodic and cathodic peak currents were measured and the values depended on scanning rate and ion concentration when the solution was static. With the flowing solution, limiting currents were observed and the anodic limiting current was increased with the cubic root of the solution flow rate.