心电地图仪中工频干扰的一种滤除方法

在心电地图仪中记录到的体表心电信号往往由于电磁的影响而引进工频干扰．基于体表心电信号中工频干扰的特点，作者提出了一种滤除工频干扰的方法，即就单独—胸导联信号通过提高频谱的分辨率来估计工频干扰的频率；基于最小均方误差准则来估计各导联信号中工频干扰的幅度和相位。文中还给出了该算法的流程图和滤波性能分析。模拟结果表明了该算法的有效性。应用该算法对心电地图仪中的工频干扰进行对消，取得了满意的结果。     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

双塔脱丙烷工艺技术

对扬子乙烯装置双塔脱丙烷系统低压塔液泛、高压塔再沸器堵塞等问题进行了技术分析,提出了工艺流程修改方案,完善了双塔脱丙烷技术,对同类装置有参考价值。     

COATES GRAPH APPROACH FOR GENERATING SYMBOLIC NETWORK FUNCTION

In this paper, symbolic code matrix ,constant matrix and count matrix are defined .The first twomatrices are used to describe the elemental expression of augmented matrix and the nede admittance equa-tion is thus obtained. The third matrix is used to obtain the incoming degree matrix, and according to thematrix all the 1- factors of the Coates graph are given. By using the data code, the determinant is expandedand the same items in the expansion are merged. Thus the symbolic network function in which no term can-cellation occurs is generated.     

NADRA 3D information technology for analysis of processes in multicomponent soil media

This paper considers the principles of algorithmic and software implementation of the software system NADRA 3D designed to analyze processes in three-dimensional multicomponent soil media. The principles of operation of NADRA 3D are described. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 6, pp. 157–174, November–December 2006.     

中变催化剂失活典型事例剖析

通过2起中变催化剂失活的事件，从理论上剖析其根源，并探讨防范的对策。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。     

甲醇氧化羰化制碳酸二甲酯产物气相色谱分析

以Chromosorb 10 1为固定相 ,气相色谱法分析甲醇氧化羰化制碳酸二甲酯产物中水、甲醇、乙酸甲酯和碳酸二甲酯等组份的含量 ,考察了柱温 ,载气流量对分离度的影响 ,确定了适宜的分析条件 ,并用校正面积归一化法定量。该方法操作简便 ,快速 ,精度高 ,重现性好     

分析型全蒸发器在啤酒挥发性成分测定中的应用

综述了分型全蒸发器技术在啤酒发酵过程中的应用状况，并介绍了分析型全蒸发器模型结构及与之配合使用的连续多分支管。     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.