小方坯连铸机的PLC自动控制

本文对弧型小方坯连铸机工艺与设备进行了分析，介绍了连铸生产的ＰＬＣ控制系统。及其软件设计。     

智能温湿度测控仪

本文提出一种利用MCS-51系列单片机实现温湿度自动检测和控制的智能仪表,文中对仪器的工作原理、硬件组成和软件设计作了较为详细的介绍。     

引进型国产300MW汽轮机窜轴事故分析及防止对策

通过引进型国产300MW汽轮机在启动试运中出现的一次窜轴事故,根据计算机追忆打印的有关图表、数据分析了产生事故的原因,并提出了为防止类似事故重演应采取的措施和建议。经采取措施后该机组多次又在相同情况下启机,已安全运行。说明分析正确,措施得当,值得同类型机组借鉴。     

IR2172在电机数字控制系统中的应用

IR2172是国际整流器公司推出的电流传感芯片。介绍了IR2172的结构特点和工作原理以及在永磁同步电机数字控制系统中的应用。     

催柴加氢装置分馏系统空冷改造方案的探讨

对催柴加氢装置分馏系统空冷存在的问题进行了剖析,认为两塔回流温度不能同时满足工艺需要的主要原因是2台空冷共用风机造成的,并对改造方案进行了比较。     

Ultrasonic measurement of the inter-electrode gap in electrochemical machining

During the process of electrochemical machining the dependency of the inter-electrode gap with time and process parameters can be used to determine process characteristics and to define the shape of the workpiece surface relative to the tool surface. Defining process variables to map out the required gap-time function requires the use of time-consuming iterative trials. In-line monitoring of the gap would enable process control and tool to workpiece transfer characteristics to be achieved (for ideal conditions) without the requirement to generate such parameter maps. This work explores the use of ultrasound applied as a passive, non-intrusive, in-line gap measurement system for ECM. The accuracy of this technique was confirmed through correspondence between the generated gap-time and current time data and theoretical models applicable to ideal conditions. Gap measurements are also used to demonstrate and quantify the degree of departure from ideal behaviour for an In718/chloride system as the electrolyte flow rate is reduced from 16 to 4 l min⁻¹. The monitoring of the gap size has also been shown to be effective when determining shape convergence under ideal conditions, for the example case of a 2D sinusoidal profile.     

APDT-00三极放电管全自动打印机的研制

介绍了新近研制的APTD - 0 0三极放电管全自动打印机的结构特点及整机设计的关键技术 ,阐述了自动上料机构、打印机构和控制电路的设计     

近非临界相位匹配温度调谐MgO：LiNbO3OPO

通过对MgO:LiNbO3参量过程温度相位匹配及走离角，允许参量等运转参数的理论计算与分析，确定了晶体的切割角度θ=82℃，以近非临界相位匹配（NCPM）取代NCPM，将温度调节范围控制在较低的温度上，研制了532nm泵浦的MgO:LiNbO3温度调谐脉冲光学参数振荡器（OPO），在800～1700nm波段实现连续调谐输出。参量泵浦功率密度阈值为57.3MW/cm^2，泵浦能量约2倍阈值处，单谐振（SRO）参量转换效率为11%以上。     

板式换热器热端跑冷问题的分析及处理

１００００ｍ３／ｈ制氧机板式换热器损坏修复后，热端跑冷严重，氧气取出量不足，制氧机工况恶化，通过分析找出了原因是因某单元氧通道堵塞，并采取了处理措施。     

Integrating scheduling and control functions in computer integrated manufacturing using artificial intelligence

Proper integration of scheduling and control in Flexible Manufacturing Systems will make available the required level of decision-making capacity to provide a flexibly-automated, efficient, and quality manufacturing process. To achieve this level of integration, the developments in computer technology and sophisticated techniques of artificial intelligence (AI) should be applied to such FMS functions as scheduling. In this paper, we present an Intelligent Scheduling System for FMS under development that makes use of the integration of two AI technologies. These two AI technologies — Neural Networks and Expert Systems — provide the intelligence that the scheduling function requires in order to generate goodschedules within the restrictions imposed by real-time problems. Because the system has the ability to plan ahead and learn, it has a higher probability of success than conventional approaches. The adaptive behavior that will be achieved contribute to the integration of scheduling and control in FMS.