柳钢混铁炉炉衬结构及运行管理的技改实践

针对混铁炉使用过程中出现的各种侵蚀状况，设计采用砖砌十浇注复合炉衬结构，特别对前墙拐角和后墙中段等侵蚀快的关键部位作了有针对性的技术改进；在运行管理上，制定推行全新的工艺操作规程，取得了显著的使用效果。     

CX6112车铣复合机床设计方案的研究与探讨

文章较系统地论述了车铣复合机床设计方案的形成过程，同时分析了该设计方案的持点，并简要介绍了该产品的主要技术参数和用途，简评了该产品的技术水平。     

电信网络管理的望族——TMOS

电信管理及运营支撑是爱立信公司为公用电信网提供的有关管理及运营支撑功能的综合方案，本文介绍了其中的公网管理系统和蜂窝移动网络管理系统。     

计算机轧辊管理软件

使用计算机管理轧辊可以非常方便地查询每一条轧辊的材质、产地、车削情况使用情况及该辊的轧制产量等数据，并可根据要求打印表格或轧辊消耗报表。     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

DX centers in AlxGa1-xAs bulk alloy,AlAs/GaAs ordered,and disordered superlattices

Properties of theDX centers in Al_0.5Ga_0.5As bulk alloy (b-AL), (AlAs)₂ (GaSa)₂ ordered superlattice (o-SL) and (AlAs) _m (GaAs) _n disordered superlattice (d-SL) (m = 1, 2, 3,n = 1, 2, 3) with the same macroscopic composition were measured and compared. By deconvolution of deep level transient spectroscopy (DLTS) spectrum due to theDX center, we have found a decrease in the number of separate peaks in DLTS spectrum in an intentionally atomic ordered arrangement. Visiting Scholar of the Japan Society for the Promotion of Science. On leave from Department of Electrical Engineering, San Jose State University, San Jose, California 95192-0084, USA.     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

An empirical InSAR-optical fusion approach to mapping vegetation canopy height

Exploiting synergies afforded by a host of recently available national-scale data sets derived from interferometric synthetic aperture radar (InSAR) and passive optical remote sensing, this paper describes the development of a novel empirical approach for the provision of regional- to continental-scale estimates of vegetation canopy height. Supported by data from the 2000 Shuttle Radar Topography Mission (SRTM), the National Elevation Dataset (NED), the LANDFIRE project, and the National Land Cover Database (NLCD) 2001, this paper describes a data fusion and modeling strategy for developing the first-ever high-resolution map of canopy height for the conterminous U.S. The approach was tested as part of a prototype study spanning some 62,000 km² in central Utah (NLCD mapping zone 16). A mapping strategy based on object-oriented image analysis and tree-based regression techniques is employed. Empirical model development is driven by a database of height metrics obtained from an extensive field plot network administered by the USDA Forest Service-Forest Inventory and Analysis (FIA) program. Based on data from 508 FIA field plots, an average absolute height error of 2.1 m (r = 0.88) was achieved for the prototype mapping zone.     

浅述城市规划管理信息系统

阐述了城市规划管理信息系统的内容及其建立的方法和步骤，以及其与管理人员构成和该系统的经济效益，并指出城市规划管理信息系统利用计算机技术，科学地现代化地优化了城市规划设计与城市规划管理，为了城市建设的科学发展应加大投入，跟上时代步伐，进入城市建设的计算机时代。     

基于WEB和C/S的教务管理系统的分析与设计

本文是以河南经贸职业学院教务管理工作实现网络化管理的需求为背景而展开讨论的。文中详细阐述了基于WEB和C/S模式相结合的总体设计方案,通过分析系统功能的需求,阐述了系统功能模块的设计思想。