Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

New exact solutions of the Tzitzéica-type equations in non-linear optics using the expa function method

One specific class of non-linear evolution equations, known as the Tzitzéica-type equations, has received great attention from a group of researchers involved in non-linear science. In this article, new exact solutions of the Tzitzéica-type equations arising in non-linear optics, including the Tzitzéica, Dodd–Bullough–Mikhailov and Tzitzéica–Dodd–Bullough equations, are obtained using the exp_a function method. The integration technique actually suggests a useful and reliable method to extract new exact solutions of a wide range of non-linear evolution equations.     

A Voltage Control Method for a Distributed Line Feeder by means of Multiagent Approach

This paper proposes a method for the coordinated control of power factor by means of a multiagent approach. The proposed multiagent system consists of two types of agent: single feeder agent (F_AG) and bus agent (B_AG). In the proposed system, an F_AG plays as an important role, which decides the power factors of all distributed generators by executing the load flow calculations repeatedly. The voltage control strategies are implemented as the class definition of Java into the system. In order to verify the performance of the proposed method, it has been applied to a typical distribution model system. The simulation results show that the system is able to control very violent fluctuation of the demands and the photovoltaic (PV) generations.     

Maximum likelihood-based adaptive differential evolution identification algorithm for multivariable systems in the state-space form

Parameter estimation plays an important role in the field of system control. This article is concerned with the parameter estimation methods for multivariable systems in the state-space form. For the sake of solving the identification complexity caused by a large number of parameters in multivariable systems, we decompose the original multivariable system into some subsystems containing fewer parameters and study identification algorithms to estimate the parameters of each subsystem. By taking the maximum likelihood criterion function as the fitness function of the differential evolution algorithm, we present a maximum likelihood-based differential evolution (ML-DE) algorithm for parameter estimation. To improve the parameter estimation accuracy, we introduce the adaptive mutation factor and the adaptive crossover factor into the ML-DE algorithm and propose a maximum likelihood-based adaptive differential evolution algorithm. The simulation study indicates the efficiency of the proposed algorithms.     

Longitudinal permeability determination of dual-scale fibrous materials

In this work, the longitudinal permeability of squarely packed dual-scale fiber preforms is studied theoretically. These fiber preforms are composed of aligned porous tows and the tows are tightly packed. The effective permeability is calculated as a parallel-like network of intra-tow permeability and inter-tow permeability, which are quantified by Darcy’s law and the inscribed radius between tows, respectively. The jump velocity at the interface between inter-tow fluids and porous tows is considered, as derived by substituting Beavers and Joseph’s correlation into Brinkman’s equation. We further examine the effects of intra-tow permeability on the effective permeability of the fibrous system with three interface conditions: (1) interface velocity = 0, (2) interface velocity = mean intra-tow velocity, and (3) interface velocity = jump velocity. The jump-velocity-based model is found to be closest to numerical data. The influence of the fiber volume fraction of tows on the effective permeability is also analyzed.     

Integral barrier Lyapunov function-based adaptive fuzzy output feedback control for nonlinear delayed systems with time-varying full-state constraints

In this article, an adaptive fuzzy output feedback control method is presented for nonlinear time-delay systems with time-varying full state constraints and input saturation. To overcome the problem of time-varying constraints, the integral barrier Lyapunov functions (IBLFs) integrating with dynamic surface control (DSC) are applied for the first time to keep the state from violating constraints. The effects of unknown time delays can be removed by using designed Lyapunov-Krasovskii functions (LKFs). An auxiliary design system is introduced to solve the problem of input saturation. The unknown nonlinear functions are approximated by the fuzzy logic systems (FLS), and the unmeasured states are estimated by a designed fuzzy observer. The novel controller can guarantee that all signals remain semiglobally uniformly ultimately bounded and satisfactory tracking performance is achieved. Finally, two simulation examples illustrate the effectiveness of the presented control methods.     

A review of topic modeling methods

Topic modeling is a popular analytical tool for evaluating data. Numerous methods of topic modeling have been developed which consider many kinds of relationships and restrictions within datasets; however, these methods are not frequently employed. Instead many researchers gravitate to Latent Dirichlet Analysis, which although flexible and adaptive, is not always suited for modeling more complex data relationships. We present different topic modeling approaches capable of dealing with correlation between topics, the changes of topics over time, as well as the ability to handle short texts such as encountered in social media or sparse text data. We also briefly review the algorithms which are used to optimize and infer parameters in topic modeling, which is essential to producing meaningful results regardless of method. We believe this review will encourage more diversity when performing topic modeling and help determine what topic modeling method best suits the user needs.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.