用不稳定试井资料研究油藏储集层流动系统模式：以准东油区为例

从不稳定试井Ｈｏｒｎｅｒ曲线形态分类入手，结合油藏动态特征对油藏储集层流动系统进行分类，并初步确定出各类流动系统的特征参数及其相应的开采特点。根据不稳定试井Ｈｏｒｎｅｒ曲线形态，可以把相应的储集层流动系统划分为三大类（孔隙流动系统、双重介质流动系统、裂缝流动系统）五个亚类。特别提出了双重介质孔缝串并流动系统组合模式。这无论对新区开发方案的编制，还是老区开发政策的制定都具有重要的借鉴参考价值。     

具有减少辨识参数的随机多变量极点配置自适应控制器

本文提出了一种新的限制输出个数减少随机多变量自适应控制中辨识参数的方法，并给出了减少辨识参数的极点配置自适应算法。虽然采用ｎ个输入１个输出的减少辨识参数的模型来设计控制器，但所提出的控制器能够保证被控系统的几个输出跟踪参考输入信号，仿真结果表明，所提出的方法是成功的。     

On the boundary-layer control through momentum injection: Studies with applications

The concept of moving surface boundary-layer control, as applied to a Joukowsky airfoil, is investigated through a planned experimental programme complemented by numerical studies. The moving surface was provided by rotating cylinders located at the leading edge and/or trailing edge as well as top surface of the airfoil. Results suggest that the concept is quite promising, leading to a substantial increase in lift and a delay in stall. Depending on the performance desired, appropriate combinations of cylinder geometry, location and speed can be selected to obtain favourable results over a wide range of angle of attack. Next, effectiveness of the concept in reducing drag of bluff bodies such as a two-dimensional flat plate at large angles of attack, rectangular prisms and three-dimensional models of trucks is assessed through an extensive wind tunnel test-programme. Results show that injection of momentum through moving surfaces, achieved here by introduction of bearing-mounted, motordriven, hollow cylinders, can significantly delay separation of the boundary-layer and reduce the pressure drag. The momentum injection procedure also proved effective in arresting wind-induced vortex resonance and galloping type of instabilities. A flow visualization study, conducted in a closed-circuit water tunnel using slit lighting and polyvinyl choride tracer particles, adds to the wind-tunnel and numerical investigations. It shows, rather dramatically, the effectiveness of the moving surface boundary-layer control (MSBC). The Sabita Chaudhury Memorial Lecture The models were fabricated in the Mechanical Engineering Workshop. The assistance of M/s E Abell, P Hurren and D Camp in the design and construction of the models is gratefully acknowledged. The investigation was supported by the Natural Sciences and Engineering Research Council of Canada, Grant No. A-2181.     

The formalization and analysis of a communications protocol

The MSMIE protocol [SBC89] allows processors in a distributed system to communicate via shared memory. It was designed to meet the reliability and efficiency needs of applications such as nuclear safety systems. We present a formal model of the MSMIE protocol expressed in the notation CCS. Desirable properties of the protocol are expressed in the modal mu-calculus, an expressive modal logic. We show that the protocol lacks an important liveness property. In actual operation, additional operating constraints are checked to avoid potential problems. We present a modified protocol and show that it possesses the liveness property even without checking operating constraints. We also show how parts of the analysis were automated with the Concurrency Workbench.     

相似理论在真空灭弧室研究和设计中的应用

本文应用相似理论得出,真空灭弧室中电弧运动速度与电流强度成线性关系的相似准则,和极限开断电流与触头直径、开距间的经验公式。认为用小电流模型来研究大电流真空灭弧室是可行的。     

CO2 abatement by co-firing of natural gas and biomass-derived gas in a gas turbine

In this work, a possible way for partial CO₂ emissions reduction from gas turbine exhausts by co-firing with biomass is investigated. The basic principle is the recirculation of a fraction of the exhausts (still rich in oxygen) to a gasifier, in order to produce syngas to mix with natural gas fuel. As biomass is a CO₂ neutral fuel, the fraction of replaced natural gas is a measure of CO₂ removal potential of the powerplant.     

齿轮减速器造型设计与模态分析

讨论复杂结构的建模方法,建立齿轮减速器三维实体模型并进一步建立了齿轮减速器的三维有限元模型,分析系统的固有特性,从而获得了设计所需的必要数据。     

镁法海绵钛生产工艺中大型无隔板镁电解槽的节能实践

以镁法海绵钛生产工艺中大型无隔板镁电解槽的实际节能情况为例，探讨了在镁电解生产中的非生产耗电、生产耗电、漏电等因素造成的能量浪费，阐述了生产中粗镁直流电耗、电流效率、工作电压3者之间的关系，指出了影响电解槽工作电压的有关因素及降低电解槽工作电压的途径。     

浅谈降低电解槽氟化铝单耗的方法

氟化铝是电解生产中十分重要的原料，它对控制电解槽电解质温度，保持电解槽技术条件发挥着重要的作用。但随着电解生产成本的逐渐降低，氟化铝的消耗成为电解生产成本中的一项重要内容。本文就某分厂电解槽氟化铝添加的生产工艺、设备、控制以及管理等方面，提出降低氟化铝单耗的简要方法。