纳米SiO2粉体的制备与研究

纳米SiO2粉体的制备是以硅酸钠和盐酸为原料，添加适宜的稳定剂(非离子表面活性剂)和分散剂，在适宜的pH值和温度下，采用化学沉淀法合成。研究表明，要得到性能优良纳米的SiO2粉体，最佳工艺条件为：温度20～40℃，pH=6，反应液质量浓度P1=20g／L，P2=1．20g／L，反应时间15min。结果表明：制备的纳米SiO2粒径30～50nm，比表面积大，分散性好，质量优良，可达到产业化的生产。     

MoNoC: A monitored network on chip with path adaptation mechanism

Complex systems on chip containing dozens of processing resources with critical communication requirements usually rely on the use of networks on chip (NoCs) as communication infrastructure. NoCs provide significant advantages over simpler infrastructures such as shared busses or point to point communication, including higher scalability, more efficient energy management, higher bandwidth and lower average latency. Applications running on NoCs with more than 10% of bandwidth usage attest that the most significant portion of message latencies refers to buffered packets waiting to enter the NoC, whereas the latency portion that depends on the packet traversing the NoC is sometimes negligible. This work presents an adaptive routing architecture, named Monitored NoC (MoNoC), which is based on a traffic monitoring mechanism and the exchange of high priority control packets. This method enables to adapt paths by choosing less congested routes. Practical experiments show that the proposed path adaptation is a fast process, enabling to transmit packets with smaller latencies, up to 9 times smaller, by using non-congested NoC regions.     

Mössbauer analysis of iron phases in brown coal ash and fireside deposits

The iron phases present in an electrostatic precipitator ash, an uncooled ash deposit and a cooled superheater ash deposit from Hazelwood Power Station, Australia, burning Morwell brown coal has been examined using Mössbauer spectroscopy. The principal iron phase in the precipitator ash and the uncooled ash deposit from a hot gas offtake was calcium aluminoferrite (Ca₂Fe_{2 ? x}Al_xO₅). Minor amounts of hematite (α-Fe₂O₃) and magnetite (Fe₃O₄) were also detected in the precipitator ash. The cooled superheater ash deposit contained a (Mg, Fe, Al) oxide spinel as the primary iron phase; small quantities of hematite were also detected in this deposit close to the heat exchanger interface. The formation of these iron phases has been rationalized on the basis of the average composition of coal delivered to the power station and supplementary ash chemistry data obtained from other techniques. The evidence suggests that the calcium aluminoferrite in the precipitator ash is derived from inorganic constituents (distributed throughout the coal organic matrix) and the hematite and magnetite are of mineral origin (discrete particles).     

关于体育教学改革的问题探讨

分析体育课教学中的主要任务、教材内容、教学方法、成绩考核等几个问题,并对此进行初步的研究和探讨,提出改革意见和措施,以改善体育课的教学效果。     

陶瓷原料中二氧化硅分析方法的对比与选择

本文综合各种文献 ,对陶瓷原料中SiO2 的各种分析方法的优缺点 ,使用条件 ,应用侧重点进行了比较与评述     

民办高校深入开展党的群众路线教育实践活动的探究

民办高校有着与公办高校不同的管理体制和机制,为了更加深入、更加有效地开展党的群众路线教育实践活动,要结合特点和发展的实际,科学制定活动方案、强化针对性,真正解决工作中存在的问题,正确地处理几个共性问题,有效凝聚学校发展的力量,推动中国高等教育事业全面健康可持续发展。     

Effects of expanding zone parameters of vacuum dust suction mouth on flow simulation results

Based on the parametric analysis of the expanding zone of the vacuum dust suction mouth, the flow in the vacuum dust suction mouth was simulated by computational fluid dynamics （CFD） software, Fluent. The effects of the expanding zone parameters on flow simulation were analyzed. The results show that simulation effects depend on threshold values of the expanding zone parameters of the dust suction mouth, and the threshold values of the expanding zone can be obtained according to the different structures of the vacuum dust suction mouth and be selected as the geometric parameters in calculating, and also corners of the expanding zone make unobvious difference in calculation accuracy and in computational efficiency compared with no corner. The simulation results provide practical guidance to the flow simulation on the dust suction mouth.     

A computational fluid dynamic analysis of gas and particle flow in flame spraying

The flame spraying process, which is a common industrial thermal spraying application, has been analyzed by means of three-dimensional computational fluid dynamics (CFD) simulations. The process used at the Volvo Aero Corporation for the coating of fan and compressor housings has been modeled. The process uses the Metco 6P torch (Metco, Westbury, NY), which ejects a mixture of acetylene and oxygen at high speed through a ring of 16 orifices to form the flame. A stream of argon gas flowing through an orifice in the center of the ring carries a powder of nickel-covered bentonite through the flame to the spray substrate. The torch is cooled by a flow of air through an outer ring of 9 orifices. The simulation emulated reality closely by including the individual inlets for fuel, cooling air, and injected particles. The gas combustion was simulated as a turbulent, multicomponent chemically reacting flow. The standard, two-equation k-ε turbulence model was used. The chemical reaction rates appeared as source terms in the species transport equations. They were computed from the contributions of the Arrhenius rate expressions and the Magnussen and Hjertager eddy dissipation model. The first simulations included several intermediate chemical substances whose predicted concentration agreed favorably with measurements. Later, more simplified simulations incorporated only the global chemical reaction involving the initial and the final products, with corrections to the thermal properties being made to account for the missing intermediaries. The gas velocity and temperature fields predicted by the later simulations compared satisfactorily to those predicted by the earlier, more elaborate, ones. Therefore, the final simulations, which incorporated injected particles, were conducted employing the simplified model with only the global reaction. An in-house finite difference code was developed to calculate particle properties. Allowance was made for elliptical shapes, phase changes, and internal heat transfer with regard to the composite material. The particle velocities and temperatures predicted by the final simulations compared fairly well with experimental results obtained with the optical DPV2000 system.     

Knowledge and Belief: Some Clarifications

The notions of knowledge and belief play an important role in philosophy. Unfortunately, the literature is not very consistent about defining these notions. Is belief more fundamental than knowledge or is it the other way around? Many accounts rely on the widely accepted strategy of appealing to the intuition of the reader. Such an argumentative methodology is fundamentally flawed because it lets the problems of common sense reasoning in through the front door. Instead, I suggest that philosophical arguments should be based on formal-computational models to (a) reduce the ambiguities and uncertainties that come with intuitive arguments and reasoning, and (b) capture the dynamic nature of many philosophical concepts. I present a model of knowledge and belief that lends itself to being implemented on computers. Its purpose is to resolve terminological confusion in favor of a more transparent account. The position I defend is an antirealist naturalized one: knowledge is best conceived as arising from experience, and is fundamental to belief.