Use of palm oil-based biofuel in the internal combustion engines: Performance and emissions characteristics

Palm oil (PO) was treated using different methods in order to use and test it as fuel in Compression Ignition (CI) engines. The treatments include PO preheated and preparation of PO/diesel oil blends, using mixtures of PO with waste cooking oil (WCO), which are converted into esters by a transesterification process. The purpose of this study is to evaluate the potential of the palm oil-based biofuels to replace diesel oil in CI engines.Tests were conducted in a single cylinder, four-stroke, air-cooled, direct injection diesel engine (no engine modifications were required). Experiments were initially carried out with diesel oil for providing baseline data. All the tested fuels have a low heating value compared to diesel fuel. A high fraction of PO in diesel fuel decreases the heating value of the blend. The brake thermal efficiency increases for the PO/Diesel blends. HC emissions for all those fuels except for the PO/Diesel blends are found lower, while CO emissions rise for all types of fuels. NO_x emissions are higher at low load, but lower at full load, for the engine fueled with PO and lower both at middle and full load for the engine fueled with the esters.     

The current status and perspectives of biofuel production via catalytic cracking of edible and non-edible oils

Biofuel development has gained the attention of researchers in recent years owing to the rate of depletion of fossil fuels. Several processes are currently employed in the conventional production of different biofuels: the production of biodiesel is catalytically performed either through the transesterification of triglycerides using alcohol or the deoxygenative ecofining of triglycerides in a non-alcohol environment; bio-oil is produced by the pyrolysis of biomass; bio-ethanol is produced by the fermentation of sugars obtained from starch or cellulosic based biomass, while bio-gasoline is produced from the catalytic cracking of triglycerides. Owing to the enormous dependency of transport vehicles running on gasoline engines, the development of bio-gasoline may well reduced the dependence of the fuel market on fossil fuels. The present article summarizes recent progresses and future prospects of biofuel production via catalytic cracking technology. This technology can be implemented in current petroleum refineries with minor modifications. However, reactor design and catalyst choice are important issues and have to be addressed before successful implementation of this technology in commercial ventures.     

Life cycle assessment of two palm oil production systems

In 2009 approx. 40 Mt of palm oil were produced globally. Growing demand for palm oil is driven by an increasing human population as well as subsidies for biodiesel and is likely to increase further in coming years. The production of 1 t crude palm oil requires 5 t of fresh fruit bunches (FFB). On average processing of 1 t FFB in palm oil mills generates 0.23 t empty fruit bunches (EFB) and 0.65 t palm oil mill effluents (POME) as residues. In this study it is assumed that land use change does not occur. In order to estimate the environmental impacts of palm oil production a worst and a best case scenario are assessed and compared in the present study using 1000 kg of FFB as functional unit.The production and treatment of one t FFB causes more than 460 kg CO_2eq in the worst case scenario and 110 kg CO_2eq in the best case scenario. The significant greenhouse gas (GHG) emission reduction is achieved by co-composting residues of the palm oil mill. Thus treating those residues appropriately is paramount for reducing environmental impacts particularly global warming potential (GWP) and eutrophication potential (EP).Another important contributor to the EP but also to the human toxicity potential (HTP) is the biomass powered combined heat and power (CHP) plant of palm oil mills. Frequently CHP plants of palm oil mills operate without flue gas cleaning. The CHP plant emits heavy metals and nitrogen oxides and these account for 93% of the HTP of the advanced palm oil production system, of which heavy metal emissions to air are responsible for 79%. The exact emission reduction potential from CHP plants could not be quantified due to existing data gaps, but it is apparent that cleaning the exhaust gas would reduce eutrophication, acidification and toxicity considerably.     

Optimization and characterization studies on bio-oil production from palm shell by pyrolysis using response surface methodology

In this work palm shell waste was pyrolyzed to produces bio-oil. The effects of several parameters on the pyrolysis efficiency were tested to identify the optimal bio-oil production conditions. The tested parameters include temperature, N₂ flow rate, feed-stock particle size, and reaction time. The experiments were conducted using a fix-bed reactor. The efficient response surface methodology (RSM), with a central composite design (CCD), were used for modeling and optimization the process parameters. The results showed that the second-order polynomial equation explains adequately the non-linear nature of the modeled response. An R² value of 0.9337 indicates a sufficient adjustment of the model with the experimental data. The optimal conditions found to be at the temperature of 500 °C, N₂ flow rate of 2 L/min, particle size of 2 mm and reaction time of 60 min and yield of bio-oil was approximately obtained 46.4 wt %. In addition, Fourier Transform infra-red (FT-IR) spectroscopy and gas chromatography/mass spectrometry (GC-MS) were used to characterize the gained bio-oil under the optimum condition.     

Study of the response of the area of the palm to impact: Relationship between the physical characteristic of the palm impact and the subject perception of the severity of the palm impact

Even though using the hand as a hammer causes injury, the practice continues, and may be increasing, in industry and in jobs that require intensive manual labor. This was an exploratory study aimed at measuring the relationships between the forces of strikes, the relative angles of strikes, and/or the number of strikes (up to 3) with the perception of severity of strikes when using the base of the palm of the hand. Eight subjects struck a metal force plate with the base of the palm of the hand at three levels of force, three levels of angle with respect to the surface of a force plate, and with three different numbers of times in a trial. Subjects were then asked to give a psychophysical rating after each trial. The subjective perception of the severity of each impact and force-time curves were recorded. From each force-time curve, peak force, maximum acceleration of force application, and the area of the force curve from initiation to peak were determined. Sixteen ANOVA models were analyzed.     

Influence of Processing Conditions on the Physicochemical Properties and Shelf-Life of Spray-Dried Palm Sugar (Arenga pinnata) Powder

The influence of spray-drying conditions on some physicochemical properties of palm-sugar powder ( Arenga pinnata ) was studied. Twenty tests were carried out according to a central composite design. Independent variables were: inlet temperature (150–190°C), feed flow rate (9–21 g/min), and maltodextrin concentration (14–25%). Process yield, hygroscopicity, and outlet temperature were analyzed as responses. Results revealed that increasing inlet temperature resulted in higher process yield and outlet temperature and a lower hygroscopicity. Similarly, higher inlet temperature led to lower moisture content, dissolution rate, and total phenolic content of the powder. Conversely, the feed flow rate negatively influenced process yield and hygroscopicity, and positively influenced moisture content. Moreover, maltodextrin exhibited negative influence on process yield and hygroscopicity, respectively. Moreover, storage (30°C, six months) led to noticeable losses in flowability and wettability. Powder morphology was also influenced by the inlet temperature. Lower inlet temperature resulted in particles with shrivelled surfaces while higher temperature produced a greater number of larger particles with smooth surfaces.     

Start-up study of biohydrogen production from palm oil mill effluent in a lab-scale up-flow anaerobic sludge blanket fixed-film reactor

A start-up study of lab-scale up-flow anaerobic sludge blanket fixed-film reactor (UASFF) was conducted to produce biohydrogen from palm oil mill effluent (POME). The reactor was fed with POME at different hydraulic retention time (HRT) and organic loading rate (OLR) to obtain the optimum fermentation time for maximum hydrogen yield (HY). The results showed the HY, volumetric hydrogen production rate (VHPR), and COD removal of 0.5–1.1 L H₂/g COD_consumed, 1.98–4.1 L H₂ L^?1 day^?1, and 33.4–38.5%, respectively. The characteristic study on POME particles was analyzed by particle size distribution (PSD), Scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDX). The microbial Shannon and Simpson diversity indices and Principal Component Analysis assessed the alpha and beta diversity, respectively. The results indicated the change of bacterial community diversity over the operation, in which Clostridium sensu stricto 1 and Lactobacillus species were contributed to hydrogen fermentation.     

Measuring factors affecting grip strength in a Taiwan Chinese population and a comparison with consolidated norms

We inquire whether assessment of an individual's upper limb function may be improved by using specific regional norms rather than consolidated global norms. Grip strengths were measured in a sample of 482 adults across Taiwan, and compared with consolidated norms. To ensure comparable conditions, our procedures were those recommended by the American Society of Hand Therapists (ASHT). Overall the mean grip strength of our sample was significantly (male 25%, female 27%) lower than consolidated norms derived from largely Caucasian populations. We investigated variables that might relate to this divergence. Results of ANOVA and stepwise multiple regression analysis showed that gender, age and palm length were effective predictors in grip strength. A regression equation was derived. When other variables were matched, palm length appeared an important discriminating factor. Further anthropometric and socio-economic factors also need investigation. Specific regional norms should provide more accuracy for ergonomists and health workers assessing an individual's upper limb function, and may avoid errors in appraisal. This paper suggests grip strength values for Taiwan.     

基于掌纹图象分析的身份识别系统

研究了人体掌纹的生物测定学特征,掌纹图象的边界提取,建立了具有唯一性和可识别性的掌纹图象特征空间,设计了用于掌纹图象识别的ＡＲＴ２神经网络,并在此基础上建立了快速、可靠性高的新型身份识别系统。