停棒子系统与控制棒组操作范围监测试验

本文叙述了反应堆保护系统停棒与汽轮机降功率子系统的系统功能、保护参数和秦山核电站控制棒组插入监测器的设计与参数选择,确定了控制棒提升上极限值和在不同工况下棒插入低位、低-低位整定值,并在热态零功率条件下加以验证。试验证明参数选择是合理的,为功率运行阶段提供了数据。     

Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

一种900-MHz 20-mW CMOS功率放大器的设计

提出了一个工作电压为3V，工作频率900MHZ，输出功率为20mW的高效率CMOS功率放大器。为了达到设计目标，文章采用了一些特殊的方法，包括三级放大结构，级间的调谐匹配和层叠差分结构。     

Interpolating Quintic Polynomial with C~1 Continuity

A method constructinq C~1 Piecewise quintic polynomial over a triangular grid to interpo-late function values and partial derivatives at vertices is presented in this paper.The set of precise poly-nomials of this method is discussed.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

AutoCAD 下非结构网格自动生成

在AutoCAD环境下，从背景网格生成和数据结构两方面对推进阵面法进行修正。采用修理后的方法，使得在流场、泥沙输移和床面冲淤数值计算的前处理过程中无须精心预设内部控制点而只需给边界一个尺度，就能自动生成适应任意复杂边界的非结构网格，从而提高网格生成、优化的效率和通用性。     

钻机柴油机的动向和190系列柴油机的发展

本文概括介绍了国内外钻机柴油机发展的水平及动向,比较了国内钻机柴油机与国外钻机柴油机在发展上的差距。重点介绍了作为国产钻机主要动力的190系列柴油机的发展状况及最新技术在该机型上的应用。     

缝纫设备输送动力装置的分析

文章介绍了几种缝纫设备输送动力装置的送布原理，认为应针对不同的面料特性及经制工艺要求，选用合适的设备输送系统。     

Effects of low radiation on the power quality of a distributed PV-grid connected system

We have previously investigated effects of radiation levels on power quality of a number PV-grid interactive systems in Thailand, in terms of harmonics and voltage variation at the point of common coupling (PCC). In this paper, we focus on the nature of components of complex power (actual, reactive and apparent power) of inverter output of a PV-grid interactive system due to low radiation, below 400 W/m². The system being investigated has an array of 4.2 kWp and representative of roof top units. It is observed that a PV array supplies increasing real power, in magnitude and as percentage of complex power, at high values of radiation. At low radiation level when the array does not provide enough output power, reactive power is drawn from distribution transformer and fed into an inverter and loads. Based on results from the test site and long term radiation data of Bangkok, we then estimate energy available from low radiation from a hypothetical PV-grid interactive unit in Bangkok of a similar size. It can be seen that for a tropical climate like Thailand a significant amount of energy, 20–30% of radiation energy, is in the form of reactive power. Methods must be devised to capture this low radiation energy and converted into real power form.