小高层剪力墙结构开洞设计探讨

小高层建筑需通过剪力墙开洞(结构开洞)降低侧向刚度,本文对开洞部位以及墙肢和连梁设计提出一些看法,供设计人员参考。     

Thermal expansion characteristics of a titanium modified austenitic stainless steel: measurement by high-temperature X-ray diffraction and modelling using Grüneisen formalism

The thermal expansion of a titanium modified, swelling resistant austenitic stainless steel designated as D9 is studied by measuring the lattice parameter as a function of temperature in the range 300-1300 K by high-temperature X-ray diffraction technique. The thermal expansion data thus obtained is in reasonable agreement with the typical thermal expansion values reported for similar nuclear grade austenitic stainless steels. However, at temperatures exceeding 900 K, the measured thermal expansivity exhibits a pronounced non-linear increase due partly to the precipitation of complex carbide and intermetallic phases. The high-temperature thermal expansion data obtained in the present study are augmented by modelling the low-temperature thermal expansion behaviour by Grüneisen formalism.     

Analysis of characteristic odors from human male axillae

A number of studies concerning the analysis of axillary odors have assumed that the characteristic odor produced in the axillae is due to volatile steroids and isovaleric acid. Organoleptic evaluation of Chromatographic eluants from axillary extracts was employed to isolate the region in the chromatogram where the characteristic odor eluted. The odor of the dissolved eluant was eliminated when it was treated with base, suggesting that acids make up the characteristic axillary odor. Subsequent extraction of the pH-adjusted axillary extract in conjunction with organoleptic evaluation of the Chromatographic eluant, preparative gas chromatography, and analysis by GC-MS as well as GC-FTIR showed the presence of a number of C₆ to C₁₁ straight-chain, branched, and unsaturated acids as important contributors to the axillary odor. The major odor component is (E)-3-methyl-2-hexenoic acid. Three homologous series of minor components are also important odor contributors; these consist of the terminally unsaturated acids, the 2-methyl-C₆ to -C₁₀ acids and the 4-ethyl-C₅ to -C₁₁ acids. These types of acids have not been reported previously as components of the human axillary secretions and have not been proposed previously as part of the principal odor components in this area.     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Scaling laws and internal structure for characterizing electrospun poly[(R)-3-hydroxybutyrate] fibers

Using chloroform/dimethylformamide (CF/DMF) co-solvent, electrospinning of poly[(R)-3-hydroxybutyrate] (PHB) solutions was carried out at ambient temperature. The effects of the applied voltage (V), flow-rate (Q), and solution viscoelastic properties on the Taylor cone, electrified jet, and fiber morphology were investigated. In addition, the electric field developed by the needle-plate electrode configuration was calculated using a finite element analysis to reveal the tip-to-collector (H) effect. Among the processing parameters (V, Q and H), it was found that Q played a key role in determining the jet diameter (d_j) and electrospun fiber diameter (d_f), and scaling laws existed between them, i.e., d_j-Q^0.61 and d_f-Q^0.33. The diameter reduction ratios of D_o/d_j (D_o is the needle diameter) and d_j/d_f were measured as 50-120 and 5-10, respectively; it suggested that major jet stretching took place in the straight electrified jet region, and further chain orientation could be gained by the subsequent process of jet whipping. By changing PHB concentrations from 5 to 15 wt%, the solution viscosity (η_o) was increased from 100 to 4900 cP, whereas the surface tension and solution conductivity remained unchanged; it provided a good model solution to exclusively reveal the η_o effect on the electrospinning process. Our results showed that the η_o-dependence of d_j and d_f also followed simple scaling laws: d_j-η_o^0.06, and d_f-η_o^0.39, with a prefactor depending on the processing variables, mainly the flow-rate. Regardless of the PHB concentrations used, the obtained PHB fibers showed a similar crystallinity fraction of ca. 0.63 and possession of major α-crystals together with a small amount of β-crystals with zigzag chain conformation.     

单相负载三相供电功率分配之PLC改造实践

介绍了单相负载一工频感应炉供电的S7-200CPU224改造实践方案.依托原有设备条件,三相功率分配同样设计采用电容、电抗进行调节,起、停及三相电流平衡控制由晶闸管 接触器形式替代原单纯采用接触器控制,有效值测量使用有别于FFT的检测算法.运行实践表明:节能降耗明显,设备故障率大幅降低,具有良好的推广应用价值.