源气体流量比对F-DLC薄膜结构的影响

以高纯石墨作靶，CHF3/Ar作源气体采用反应磁控溅射法制备出了氟化类金刚石（F-DLC）薄膜。拉曼光谱表明，CHF3相对流量的增加会引起薄膜的D峰与G峰强度之比I（D）/I（G）减小，晶粒增大，芳香环结构出例下降。红外吸收光谱分析证实了这些推论，指出这是由于薄膜中氟含量上升的结果。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

Two Isomers of C60F48: Computed Inter-isomeric Equilibrium

C₆₀F₄₈ has been known to exist in two isomeric forms of D₃ and S₆ symmetries. However, the quantum-chemical calculations have not agreed on their stability order though a near-isoenergetic picture is otherwise always encountered. In order to clarify the situation, the entropy effects are evaluated for synthetic temperatures of about 500K. The entropy evaluations suggest that the D₃ isomer should be more stable in the potential energy by 2.05-2.55 kcal/mol (to which term the ab initio data are closer than the semiempirical ones).     

美孚油回收利用的可行性实验研究

本文针对美孚油回收液与兰炼8#油混合利用进行可行性实验研究，经过重度、粘度、可燃性等方面的实验研究，表明美孚油回收液与兰炼8#油混合可以用在电动轮上并且获得良好的效果。     

利用C++Builder 5.0开发原理框图绘图软件

介绍了原理框图各种图形的数据存储方法，利用C^ Builder5.0开发了原理框图的绘图软件，实现了原理框图绘制的基本功能。     

C51嵌套汇编子程序在阻抗测试仪研制中的应用

C51嵌套汇编子程序，充分发挥了两种语言自的优势，介绍了C51调用汇编子程序的接品规则，并通过阻抗测试仪程序开发的例子予以详细说明。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Thermal expansion characteristics of a titanium modified austenitic stainless steel: measurement by high-temperature X-ray diffraction and modelling using Grüneisen formalism

The thermal expansion of a titanium modified, swelling resistant austenitic stainless steel designated as D9 is studied by measuring the lattice parameter as a function of temperature in the range 300-1300 K by high-temperature X-ray diffraction technique. The thermal expansion data thus obtained is in reasonable agreement with the typical thermal expansion values reported for similar nuclear grade austenitic stainless steels. However, at temperatures exceeding 900 K, the measured thermal expansivity exhibits a pronounced non-linear increase due partly to the precipitation of complex carbide and intermetallic phases. The high-temperature thermal expansion data obtained in the present study are augmented by modelling the low-temperature thermal expansion behaviour by Grüneisen formalism.     

试谈高炉冷却壁的检漏及维护

高炉冷却壁的检漏及维护，是炼铁工作者十分关心的问题，本文针对邯钢高炉具体情况，探讨了高炉冷却壁漏水的原因，检漏方法，漏水冷却壁的维护及预防措施。     

Hydrogen absorption by Pd-coated ZrNi prepared by using Barrel-Sputtering System

To improve the durability of hydrogen storage materials against surface poisoning by impurity gases, effectiveness of Pd-coating layer prepared by using a Barrel-Sputtering System was examined for ZrNi powder. The effectiveness of Pd-coating was evaluated by activation temperature, at which Pd/ZrNi poisoned by air could be activated to absorb hydrogen. Characterization of Pd-coated ZrNi (denoted as Pd/ZrNi) by scanning electron microscopy, electron probe microanalysis and X-ray diffraction showed that a uniform Pd-coating layer was formed with the barrel-sputtering system. It was found that the poisoned Pd/ZrNi sample could be activated even at 423 K to absorb hydrogen at room temperature. This exhibits remarkable contrast to bare ZrNi, which could be only activated appreciably above 1073 K. It is concluded that the Pd-coating by barrel sputtering is quite effective to avoid the effect of surface poisoning of powdery hydrogen storage materials. However, the activation at excessively high temperature resulted in the loss of high activity to absorb hydrogen. It was concluded that this phenomenon was associated with reactions between Pd and ZrNi to form PdZr and other byproducts.