国外全位置自动TIG管焊机中的一种新型弧长自动控制系统

管子全位置自动TIG焊时，弧长控制功能是确保焊接质量的关键，尤其在管径、壁厚公差大时，更显重要。本文介绍了POLYSOUDE公司全位置自动管焊机上的一种利用弧压传感反馈的自动控制系统。通过反复实测，证实了该系统具有很高的灵敏度和响应速率。     

型材挤压模工作带长度设计计算的数学建模

本文采用有限元方法 ,以型材挤压过程的有限元模拟为基础 ,研究了局部挤压比、挤压带面积和模孔距离对金属流动速度的影响 ,获得了型材挤压过程的变形流动规律。并综合主要模具结构参数对金属流动速度的影响 ,建立了铝型材挤压模模孔工作带设计计算的数学模型。选择实际型材零件按本文推导的公式设计了工作带长度 ,并与实验进行了验证 ,结果表明挤压效果良好。该公式可用于铝型材挤压模工作带长度设计计算     

Mathematical model of determination of die bearing length in design of aluminum profile extrusion die

Based on the finite element simulation of profile extrusion process, the effect of local extrusion ratio, die bearing area and the distance between extrusion cylindrical center and local die orfice center on mental flow velocity was investigated. The laws of deformed metal flow on profile extrusion process were obtained. The smaller the local extrusion ratio, the faster the metal flow velocity； the smaller the area of die bearing, the faster the metal flow velocity； the smaller the distance of position of local die orifice(the closer the distance of position of local die orifice from extrusion cylindrical axis), the faster the metal flow velocity. The effect of main parameters of die structure on metal flow velocity was integrated and the mathematical model of determination of die bearing length in design of aluminum profile extrusion die was proposed. The calculated results with proposed model were well compared withthe experimental results. The proposed model can be applied to determine die bearing length in design of aluminum profile extrusion die.     

钢丝绳激光在线测长方法研究

针对目前传统接触测长固有的打滑、磨损等问题,提出一种钢丝绳激光在线测长方法,利用激光成像技术、视觉检测技术以及数字图像处理技术对线结构激光器投射到钢绳表面所形成的图像纹理进行分析和处理,间接获得运动钢绳在线实时长度.实验证实,此方法能有效解决打滑、磨损等问题,同时还具备精度高的特点.     

基于不等长序列相似度挖掘的数据关联算法

针对不等长序列数据的关联问题,提出基于滑动窗口的最优匹配增权法不等长序列相似度度量算法。以较短序列作为滑动窗口遍历较长序列得到一组滑动相似度,利用这组相似度形成最优权重,加权得到不等长序列的相似度,并根据相似度大小对序列数据进行关联判决,以解决截断法相似度度量仅能反映截断序列局部相似度的问题。仿真实验验证了所提出算法对不等长序列数据关联的有效性,并对序列长度和量测误差等因素对相似度度量和关联效果的影响进行了讨论。     

Improved phase performance for rotman lens

Rotman lenses are used to obtain multiple beams from a single array. Although the beams produced by the feed antennas at focal points have no path length errors, the beams produced by feed antennas at off focal points may have large path length errors. These path length errors cause deterioration in the multiple beams. In this article, two novel methods are introduced to obtain feed curves which reduce the path length errors of off focal feed points significantly, compared with the commonly used circular and elliptical feed curves. The first method obtains feed curve points based on having zero path length error at three chosen points of the radiating array for each beam direction. The second method uses the particle swarm optimization method for obtaining optimum feed points for each beam direction. The results show that there is a very significant drop in the level of the maximum path length errors (in the order of about 1:4). © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE 23: 634–638, 2013.     

黄土地区隧道锁脚锚管作用机理分析研究

锁脚锚管在隧道施工中被广泛应用,而目前施工中锁脚锚管的长度、下插锚角度等几乎全部依靠工程经验来确定。通过有限元软件模拟了黄土隧道锁脚锚管在不同长度和角度下承担的最大内力和最大变形量,对比分析了锁脚锚管的长度、锚管下插角度与位移的关系。研究结果表明,锚管长度越长,变形越小,但最为经济的锚管长度为3 m左右;当所加锚管下插角在±30°时有利于支护内力的发挥。在研究结论基础上提出了隧道施工中应该采用的锁脚锚管合理长度及下插角度。     

基于复杂网络理论的无线传感器网络特征度量分析

通过研究复杂网络的理论,介绍了复杂网络的几种主要特征度量,并以此分析了无线传感器网络的特性。列举了无线传感器网络的节点度分布、集聚系数、平均路径长度、网络联通性等特性。研究了节点数、通讯半径、连通率间的关系,由仿真的数据得出,增加节点不能完全保证网络的联通,只能增加联通的概率,而增加通讯半径则可以迅速地使网络联通。因此,在条件允许的情况下,选择通讯半径大的传感器比增加撒布节点更能保证网络的联通。最后给出了适合于无线传感器网络的介数的评价方法。