汽车计算平台工程国外相关标准概述

结合我国汽车计算平台工程,分析了国外相关的标准现状和基本框架,并为今后工作的开展提出了建议.     

微制造平台微振动的最优控制

采用混合隔振技术建立了微制造平台隔振系统。该系统以空气弹簧和橡胶层作为被动隔振元件、超磁致伸缩致动器作为主动隔振元件，并采用最优控制理论设计其主动控制器。研究了在不同的性能指标加权阵的情况下，该主动振动控制系统对基础干扰和由微制造设备产生的直接干扰所引起的微制造平台振动的控制效果。研究表明性能指标加权阵对振动控制效果影响非常大。通过大量的仿真实验确定了一组性能指标加权阵，使所设计的主动控制系统能在较宽的频率范围对基础干扰和直接干扰所引起的微制造平台振动进行有效的控制。     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

地杂波O．94μm激光后向反射率测试研究

通过对地杂波O．94μm激光后向反射率的测试，获取不同入射角的多背景后向反射率测试数据。通过对测试数据的分析处理提供特征信息，为激光探浏器设计提供依据。     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

用仿真工具优化车辆动力系统(一)

在本文的第一部分，介绍了一种理想的车辆动力系统的计算机辅助开发过程。它显示了现代仿真技术在产品持续发展过程中的作用，该技术采用硬件回路作非在线的仿真，并通过现代化的试验手段对车辆进行匹配。特别重要的是提供了将电控变速器和发动机控制单元综合的可能性。接着是在线仿真在诸如发动机和变速器模式方面的应用和发展，它是上述开发过程的基础。根据上述的方法论，本文论述了仿真技术已取得的成绩和将来的应用可能性。     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

第三代短波自动链路建立系统特性分析及仿真实现

分析了第三代短波自动链路建立系统的工作特性及技术特点，并对系统仿真实现的原则及一些细节问题进行了较深入的探讨，同时对仿真实现中涉及的链路质量分析（LQA）算法进行了研究。     

基于MAPINFO和VB的自来水管网信息系统的建立

介绍基于MapInfo平台，利用VB语言进行二次开发，建立自来水管网地理信息系统的关键技术及其注意的问题。     

Structural study of cubic pyrochlores based on quantum mechanical simulation

In the ideal A₂B₂O₆O′ pyrochlore structure, the x-value of O atom position is a variable parameter. In Bi_1.5ZnNb_1.5−xTa_xO₇ (BZNT) cubic pyrochlores, the x-values alter with the different compositions of Nb/Ta. In this work, a series of initial models for BZNT were established by analyzing X-ray diffraction data. Then three structure modifying methods, including Rietveld refinement, Rietveld refinement with energy and geometry optimization based on quantum mechanics, were employed to obtain the precise models using Materials Studio. Moreover, the reflectivities of BZNT were computed by quantum mechanical simulation based on the refined models. Comparing the simulation results from different modifying models with the experimental results, it is found that Rietveld refinement with energy optimization is the most accurate method for BZNT pyrochlores. According to the simulation results, the different reflectivities correspond well with various x-values of O atom positions in BZNT pyrochlores.