低压直流供电电路中高压直流的产生

在由低压直流电源供电的电路中,往往电路的某些部位需要使用高于电源所供的电压,将电源所供的低压转换为较高的电压,常用的方法有3种:自举升压、电感升压、逆变升压。结合实际应用电路对各种升压方法从器件选择、升压原理、升压结果等诸方面进行分析、探讨,解决了总体供电电压不变时,局部高压产生的关键性问题。它对电子电器电路的设计人员有一定的启发作用,对优化电路、遴选器件有较强的参考价值。     

SOC设计中的浮动压焊块电源/地线网络设计和优化

随着VLSI工艺技术的发展和芯片规模的不断增加，尤其是在SOC设计中，原有的那种供电压焊块只能位于芯片边缘的确定益的模式已经不能够满足整个电路性能的需要。在很多情况下，依靠在电源线的拓扑结构确定后的线宽优化，还是无法保证在有限的布线资源下为电路提供可靠的高性能的供电需求。由此，出现了在芯片边缘上浮动放置压焊块及在芯片的顶部放置供电压焊块阵列的方法。文中提出了一种用于SOC设计中新的基于树型结构的浮动压焊块的电源／地线网络优化算法，经过MCNC电路实例测试后得到明显的优化结果。     

Analysis of the Datagram Congestion Control Protocol’s connection management procedures using the sweep-line method

State space explosion is a key problem in the analysis of finite state systems. The sweep-line method is a state exploration method which uses a notion of progress to allow states to be deleted from memory when they are no longer required. This reduces the peak number of states that need to be stored, while still exploring the full state space. The technique shows promise but has never achieved reductions greater than about a factor of 10 in the number of states stored in memory for industrially relevant examples. This paper discusses sweep-line analysis of the connection management procedures of a new Internet standard, the Datagram Congestion Control Protocol (DCCP). As the intuitive approaches to sweep-line analysis are not effective, we introduce new variables to track progress. This creates further state explosion. However, when used with the sweep-line, the peak number of states is reduced by over two orders of magnitude compared with the original. Importantly, this allows DCCP to be analysed for larger parameter values. Somsak Vanit-Anunchai was partially supported by an Australian Research Council Discovery Grant (DP0559927) and Suranaree University of Technology. Guy Edward Gallasch was supported by an Australian Research Council Discovery Grant (DP0559927).     

Adaptive switching supervisory control of nonlinear systems with no prior knowledge of noise bounds

The problem of controlling nonlinear noisy systems affected by parametric uncertainties is approached via the introduction of a supervisor which, whenever needed, switches on, in feedback to the plant, a controller selected from a finite set of predesigned controllers. A Lyapunov-based falsification criterion allows one to ensure robust stability in the presence of uncertain constant parameters and exogenous bounded disturbances. Simulations are discussed in order to illustrate the merits of the proposed algorithms.     

New two‐dimensional slope limiters for discontinuous Galerkin methods on arbitrary meshes

In this paper, we introduce an extension of Van Leer's slope limiter for two‐dimensional discontinuous Galerkin (DG) methods on arbitrary unstructured quadrangular or triangular grids. The aim is to construct a non‐oscillatory shock capturing DG method for the approximation of hyperbolic conservative laws without adding excessive numerical dispersion. Unlike some splitting techniques that are limited to linear approximations on rectangular grids, in this work, the solution is approximated by means of piecewise quadratic functions. The main idea of this new reconstructing and limiting technique follows a well‐known approach where local maximum principle regions are defined by enforcing some constraints on the reconstruction of the solution. Numerical comparisons with some existing slope limiters on structured as well as on unstructured meshes show a superior accuracy of our proposed slope limiters. Copyright © 2004 John Wiley & Sons, Ltd.     

Studies of elemental distributions within discrete coal macerals: Use of secondary ion mass spectrometry and X-ray photoelectron spectroscopy

Secondary ion mass spectrometry has been used to measure qualitatively the distributions of many trace and minor elements within some well-characterized coal macerals: vitrinite, fusinite and exinite. Complementary information was obtained by using X-ray photoelectron spectroscopy. Within the vitrinite specimens studied, a widely-dispersed largely inorganic aluminosilicate phase was identified, which contained a number of other trace elements. By contrast, within the organic-rich phase of this macerai, titanium was detected in a very even distribution; this suggests that some titanium may be bonded in an organic complex. The fusinite was shown to contain elevated concentrations of calcium, magnesium and fluorine, dispersed over a large portion of the maceral. The high fluorine content could be identified as an organo-fluoro compound using XPS. Exinite was found to contain lower concentrations of most elements, compared to other macerals. The organic composition of this maceral was significantly different from that of surrounding macerals; this could be seen from the enhanced emission of the C₂H₂-secondary ion and images of this ion thus clearly outlined the position of such macerals.     

Strengthening of Preloaded RC Beams Using Hybrid Carbon Sheets

Reinforced concrete (RC) beams subject to service loads of 40 or 60% of steel yielding were strengthened using hybrid continuous carbon fiber sheets. The hybrid systems were made of high-strength and high-modulus carbon sheets, and compared with systems using only high-strength carbon. It was found that the use of high-modulus carbon sheets in hybrid systems could increase the yielding load, the flexural stiffness, the postyielding ductility, and reduce the crack opening in concrete. The slope changes on load-deflection curves at steel yielding are not noticeable in hybrid systems. The tensile strains developed in hybrid sheets after the fracture of high-modulus carbon are higher in magnitude and distributed in a larger area, leading to an ultimate carbon fracture with concrete crushing. These unique features are attributed to the high stiffness and low ultimate tensile strain of the high-modulus carbon fibers which stiffen the structures, avoid or delay the fiber-reinforced polymer debonding, and facilitate the deformability during their subsequent breakdown.     

Introducing Students to Professional Practice in Civil Engineering

This paper describes a module that was introduced into a civil engineering degree program with the help of professional engineers. The aim was to develop a bridge between the world of learning and professional practice by putting students in the role of consulting engineers working with industry to produce a feasible solution to a real inquiry from a client. The module is placed in context by comparing the goals of accredited civil engineering programs in the United Kingdom and America, by describing how it is linked to the degree program and by explaining the matrix developed to identify the skills the students needed to demonstrate their ability to practice as professional engineers. Details of the module are given with examples of student work and feedback.     

Facility layout problems: A survey

Layout problems are found in several types of manufacturing systems. Typically, layout problems are related to the location of facilities (e.g., machines, departments) in a plant. They are known to greatly impact the system performance. Most of these problems are NP hard. Numerous research works related to facility layout have been published. A few literature reviews exist, but they are not recent or are restricted to certain specific aspects of these problems. The literature analysis given here is recent and not restricted to specific considerations about layout design.

We suggest a general framework to analyze the literature and present existing works using such criteria as: the manufacturing system features, static/dynamic considerations, continual/discrete representation, problem formulation, and resolution approach. Several research directions are pointed out and discussed in our conclusion.