非接触型光外差轮廓仪

本文介绍一种纳米级非接触型高精度光外差轮廓仪,它是基于普通光路的光外差干涉仪。工件表面被两束有微小频差的激光束所照射,其中一束经聚焦后用作测量光探针来扫描工件表面,另一束则用作参考光束。两束光经表面反射后产生干涉。测量信号和参考信号的相位差与表面的微不平值成正比。仪器的横向分辨率为2μm,高度分辨率为1 nm,它不需要对试样作大范围的调整,且可用试样自身作参考面。信号经光电转换后由微型计算机进行处理,它能快速完成测量、计算、显示及打印出各种参数和曲线。     

消失模生产中应用表面光泽涂料防止球铁件产生夹渣缺陷

以汽车弹簧托架为实例，分析用EPC法生产球铁件时产生夹渣缺陷的原因，提出采用表面光泽涂料可有效防止夹渣缺陷的产生，同时亦可改善铸件表面粗糙度。     

Surface characteristics of fluorine-modified PAN-based carbon fibers

Different fluorination methods were applied to modify the surface properties of carbon fibers. The relationship between the degree of fluorination and the physicochemical properties of carbon fibers was studied using a combination of mechanical tests, elemental analysis (EA), X-ray photoelectron spectrometry (XPS), and X-ray diffraction (XRD). EA and XPS analyses of fluorinated carbon fibers showed that treatment with mixtures of F₂/O₂ introduced a much higher fluorine concentration than that with F₂ only. However, XRD analysis showed that there was no increase in the interlayer distance, due to the mild fluorination condition applied. Consequently, the oxyfluorination was one of the more effective methods to increase surface polarity of carbon fibers, which probably played an important role in improving the tensile properties of the fibers in the epoxy resin system.     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.     

Approximating the problem, not the solution: An alternative view of point set matching

This work discusses the issue of approximation in point set matching. In general, one may have two classes of approximations when tackling a matching problem: (1) an algorithmic approximation which consists in using suboptimal procedures to infer the assignment, and (2), a representational approximation which involves a simplified and suboptimal model for the original data. Matching techniques have typically relied on the first approach by retaining the complete model and using suboptimal techniques to solve it. In this paper, we show how a technique based on using exact inference in simple Graphical Models, an instance of the second class, can significantly outperform instances of techniques from the first class. We experimentally compare this method with well-known Spectral and Relaxation methods, which are exemplars of the first class. We have performed experiments with synthetic and real-world data sets which reveal significant performance improvement in a wide operating range.     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Surface adsorption of comb polymers by Monte Carlo simulations

This paper reports off-lattice Monte Carlo simulations of highly-branched comb homopolymers weakly adsorbed on a flat, featureless surface showing only covolume and dispersion interactions with the adsorbate. A minimal coarse-grained model, described by hard spheres connected by harmonic springs, was employed. The interaction energy of the adsorbed combs and linear chains is first discussed as a function of the molecular mass and of the number of beads in contact with the surface. The molecular size is then investigated as a function of backbone length and branching density at a fixed arm size. The apparent swelling exponents of the adsorbed combs are larger than those of the corresponding linear chains, and much larger than that of the free molecules. This result indicates a surface-induced stiffening of the comb backbone, further studied through the persistence length l_pers. It is found that l_pers increases upon adsorption over the free-molecule value, more so the larger is the branching density. Finally, the thickness of the adsorbed layer, the surface-induced molecular anisotropy and the molecular aspect ratio are investigated as a function of branching density and molecular mass.     

Electron spectroscopies and their use for materials characterization

We present here a general overview of electron spectroscopies from a practical point of view. The most frequently used ones are described and the type of structural information they can provide on materials is explained in relation to the physical processes on which they are based. Furthermore, we explore critically and in detail various tools that have been developed to allow a systematic solving of structures by these spectroscopies.     

Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.