Johnson-Cook dynamic constitutive relationship for TC 16 titanium alloy

The true stress--strain curves of TC16 alloy with a wide range of strain rates were investigated under uniaxial quasi-static tension and uniaxial dynamic compression with the lnstron 8032 test machine and the split Hopkinson bar respectively. The results indicate that the true stress increases with increasing strain rate, while decreases with increasing temperature. Under the 105 s^-1 high strain rate and temperature higher than 673 K, the true stress would even be less than that under quasi-static condition. A new method incorporating TCl6＇s stress strain curve developing item was proposed to determine the coefficients in J-C model easily and to avoid the estimation of the adiabatic temperature rising. The Johnson-Cook dynamic constitutive relationship for TC16 was obtained for the first time. Good agreement was obtained between the model prediction and the experimental stress--strain curves for TC16 under both quasi-static and dynamic loadings.     

钛合金中亚晶的电子显微镜观察

用透射电子显微镜观察了TC6钛合金在高温退火过程中形成的亚晶(Subgrain)。合金经850℃,920℃退火后炉冷和空冷,在初生α相晶粒内形成亚晶,多为成簇分布的狭长形状,亚晶的数量随退火后冷却速度的增加而减少。亚晶界(Subgrain boundary)是由位错构成的,亚晶的形成是多边化(polygonization)的结果。     

TC11钛合金中氧铝偏析与脆性断裂

借助ＳＥＭ及ＥＤＡＸ、ＡＥＳ对某些ＴＣ１１钛合金棒材机械性能差的原因进行了研究。。结果表明材料延伸率、断面收缩率及冲击值低，显微硬度值高的拉伸和冲击断口上都呈现脆性解理断裂的断裂源，源区显微组织为条状α及空洞，且氧铝偏高。氧铝偏高造成α＋β→β相变温度和再结晶温度升高，使加工变形中形成的条状α在随后的热处理中得不到改变，并导致拉伸、冲击时的脆性断裂     

TC4合金管材挤压成型工艺研究

研究了不同的挤压温度、挤压比和挤压速度等挤压参数对TC4合金管材挤压成型工艺的影响,以及润滑方式对TC4合金挤压管材表面的影响。研究结果表明,采用热挤压方式生产φ47mm×3mmTC4合金管材,挤压比应选在3￣10之间,挤压速度选在50￣120m/s,润滑剂用玻璃粉,可得到显微组织为两相加工组织,变形充分均匀,力学性能匹配良好,表面质量合格的TC4合金管材。本研究得到的TC4合金管材挤压成型工艺研究可用于工业化生产。     

35CrMo齿轮轴探伤解剖定性

在35CrMo齿轮轴轴身最大直径部位取片进行了低倍解剖定性。结果表明,锻件内部夹杂物数量特别多,还有微裂纹和白点缺陷,因此缺陷性质被定为夹杂和白点。     

4-(6′甲基苯并噻唑-2′-偶氮)-3,5-二氨基吡唑与钯显色反应的研究和应用

对6种苯并噻唑偶氮吡唑化合物的分析特性进行了探讨,着重研究了4—(6′—甲基苯并噻唑-2′-偶氮)-3,5-二氨基吡唑(MBTAP)与钯离子显色反应的光度性质。在非离子表面活性剂 Brij35存在下与钯离子形成橙红色的配合物。适宜的 pH 值范围为9.0～10.5.配合物的最大吸收波长为510nm,表观摩尔吸光系数为3.01×10~4L·mol~(-1)·cm~(-1)。钯在0～14μg/25mL,范围内服从比尔定律.显色体系可稳定11h。在柠檬酸存在下可消除 Fe~(3+)、Co~(2+)、Cu~(2+)、Ni~(2+)等离子的干扰。     

Advancements in the design and validation of an air pollution integrated assessment model for Spain

This paper describes the design and application of the Atmospheric Evaluation and Research Integrated model for Spain (AERIS). Currently, AERIS can provide concentration profiles of NO₂, O₃, SO₂, NH₃, PM, as a response to emission variations of relevant sectors in Spain. Results are calculated using transfer matrices based on an air quality modelling system (AQMS) composed by the WRF (meteorology), SMOKE (emissions) and CMAQ (atmospheric-chemical processes) models. The AERIS outputs were statistically tested against the conventional AQMS and observations, revealing a good agreement in both cases. At the moment, integrated assessment in AERIS focuses only on the link between emissions and concentrations. The quantification of deposition, impacts (health, ecosystems) and costs will be introduced in the future. In conclusion, the main asset of AERIS is its accuracy in predicting air quality outcomes for different scenarios through a simple yet robust modelling framework, avoiding complex programming and long computing times.     

Lerisk－i*框架自动建模与编辑工具介绍

在需求工程中,基于主体的i*建模框架(主要包括策略依赖模型及策略推理模型)已经成为最常用的早期需求建模与分析的工具之一,而且关于i*建模框架的编辑工具开发也有很多相关的研究工作。然而现有的这些工具往往只提供诸如模型图编辑、存储等基本功能,而笔者需要在需求工程小组的项目中为对需求文本进行建模的结果进行模型可视化,同时提供编辑存储及自动布局功能,并开发出新的基于i*建模框架的工具。文中首先对主流的i*建模工具进行了调研,研究了建模工具的基本功能,同时分析了其功能的不足点,在此基础上提出了新工具设计的功能补充点;然后对i*框架的布局问题进行介绍并详细描述了其自动布局算法的实现,给出了可视化工具的详细设计;最后在此工具的基础上,进行了实际需求文本的建模及模型编辑功能的实验,并将此工具与主流工具的功能进行对比,以展示本工具的功能特点。     

GE RX3i系统设计与虚拟对象应用 第6讲 GERX3i在模块化加工站的设计

模块化加工系统是将定制产品的制造问题通过产品重组和过程重组转化为或部分转化为批量制造问题,即提供给用户的是全新的、定制的个性化产品,而实际产品则主要由标准的模块组成。本文介绍了GE RX3i在模块化加工站中的设计。