基于实际井眼轨迹的抽油杆柱API设计方法

目前的抽油杆柱设计方法大都基于设计井眼轨迹或经验公式，因此设计的抽油杆柱与井眼的匹配性并没有达到最优，结果可能影响了抽油杆柱的受力特性和寿命。概述了目前现有的抽油杆柱设计方法，提出了基于实际井眼轨迹的抽油杆柱API设计方法，即考虑到在三维空间中井下粘滞阻力及动载的影响，利用微单元分析方法计算出轴向载荷与轴向应力，然后在此基础上进行杆柱组合设计，并给出了设计流程。以江苏油田永21-3井为例，对几种设计方法的设计结果进行了对比分析，结果表明，江苏油田目前采用的抽油杆柱设计方法包含了人为经验因素，并不是最优的杆柱设计结果，有待进一步改进。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

A multigrid accelerated hybrid unstructured mesh method for 3D compressible turbulent flow

 A cell vertex finite volume method for the solution of steady compressible turbulent flow problems on unstructured hybrid meshes of tetrahedra, prisms, pyramids and hexahedra is described. These hybrid meshes are constructed by firstly discretising the computational domain using tetrahedral elements and then by merging certain tetrahedra. A one equation turbulence model is employed and the solution of the steady flow equations is obtained by explicit relaxation. The solution process is accelerated by the addition of a multigrid method, in which the coarse meshes are generated by agglomeration, and by parallelisation. The approach is shown to be effective for the simulation of a number of 3D flows of current practical interest. Sponsored by The Research Council of Norway, project number 125676/410 Dedicated to the memory of Prof. Mike Crisfield, a respected colleague     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

构建高扩展性的县级广电宽带数据网络

提出在县市级广电宽带数据网络的建设过程中,要着眼业务发展,突出高扩展性,构建基于标准、扩展灵活的主干网,实现网络建设的可持续性发展,并结合实际,从核心设备、端口、中继带宽、网络业务4个方面对扩展能力进行了阐述.     

化学-电解氧化法制备高铁酸钾的研究

本文用化学－电解氧化法制备高铁酸钾，克服了纯化学氧化法产品需要提纯和纯电解氧化法制备周期长的缺点，得到了高纯度的高铁酸钾晶体。     

弯曲性分叉河道中污染物扩散性的初步研究

弯曲性分叉河道中水流特征复杂,对污染物扩散有很大影响。为了定量分析其水流特征对污染物扩散的影响,采用有限元方法求解弯曲性分叉河道中的污染物扩散数学模型,研究其中污染物扩散的状况。主要针对河道回流、绕流对污染物扩散的影响进行了详细数值模拟计算,并分别给出了可视化结果及平均的扩散距离。计算结果表明:边界层稍微减弱污染物的扩散,弯道分离使污染物扩散呈现多向扩散,而回流和绕流尾迹区使污染物很难扩散,从而有利于泄漏污染物的收集和集中治理。     

Computerized IR Determination of Structural Group Composition for High-Boiling Oil Fractions

A computerized form is given of IR spectral determination for structural group composition in high-boiling oil fractions by Berthold's method (7 structural elements) and Kuklinskii's method (28 structural elements), which reduces the analysis time by factors of 3–4 and improves the accuracy.