Energy-optimal base station density in cellular access networks with sleep modes

Sleep modes are widely accepted as an effective technique for energy-efficient networking: by adequately putting to sleep and waking up network resources according to traffic demands, a proportionality between energy consumption and network utilization can be approached, with important reductions in energy consumption. Previous studies have investigated and evaluated sleep modes for wireless access networks, computing variable percentages of energy savings. In this paper we characterize the maximum energy saving that can be achieved in a cellular wireless access network under a given performance constraint. In particular, our approach allows the derivation of realistic estimates of the energy-optimal density of base stations corresponding to a given user density, under a fixed performance constraint. Our results allow different sleep mode proposals to be measured against the maximum theoretically achievable improvement. We show, through numerical evaluation, the possible energy savings in today’s networks, and we further demonstrate that even with the development of highly energy-efficient hardware, a holistic approach incorporating system level techniques is essential to achieving maximum energy efficiency.     

ATSP:时态网络可视化的自适应时间片划分方法

现有的时态网络可视化方法大多采用等量时间片来可视化网络的演变，不利于时态模式的快速挖掘和发现。为此，根据时态网络固有的特征提出自适应时间片划分方法（Adaptive Time Slice Partition method，ATSP）。在时态网络的两种表示方式（基于事件的表示方式和基于快照的表示方式）的基础上，构建了ATSP的基础模型，同时提出了一种改进模型用来描述事件间隔时间服从长尾分布的时态网络。为了实现时间片的不等量划分，针对探索任务的不同提出了基于时态模式的ATSP规则和基于中心节点的ATSP规则，并提出了实现算法--层次划分算法（Hierarchical Partition algorithm，HP）和增量划分算法（Incremental Partition algorithm，IP）。实验结果表明，ATSP方法比传统的时间片划分方法更能准确地表示网络的时态特征，且该方法应用于可视化时，能有效归纳并展示网络的特征，明显提高了视觉分析的效率。     

基于GIS单线图的配网停电单模拟操作应用研究

配电网停电会造成电力系统供配电可靠性以及服务质量下降,研究基于地理信息系统(GIS)单线图的配网停电单模拟操作应用。利用网格长度作为基本单位建立坐标系,以选取起始点与终止点为基础,通过四参数法将GIS坐标映射至图纸网格内,实现配网内设备初步布局,将杆塔、站房和整体均匀分布作为优化目标,设置多目标优化目标函数实现GIS单线图最终优化。选取某电力公司配网作为单模拟操作应用对象,模拟结果表明,单模拟操作配网停电后,该配网各负荷点年故障率、次平均停电时间以及年停电时间均有所减少,可有效提升配网的供配电可靠性。     

基于神经网络算法的井下裂缝诊断与堵漏技术

在钻井过程中，常常钻遇不同宽度的井下地层裂缝。钻遇裂缝时容易发生钻井液漏失现象，甚至发生钻井液失返现象，严重影响了安全、高效钻井。目前裂缝封堵的方法常存在封堵成功率不高、堵漏承压能力低的问题，其中一个重要的原因是对井下地层的裂缝宽度等特征认识不清。基于地层裂缝产生的岩石力学机理，确定影响裂缝宽度关键的6个力学和工程因素，并利用神经网络计算的非线性、大数据特点建立了井下地层裂缝宽度的分析模型，模型包含输入层、输出层和3个隐藏层。通过该模型诊断井下裂缝宽度，提高了计算精度，平均误差仅为2.09%，最大误差为5.88%，解决钻井现场仅凭经验判断裂缝误差较大和依靠成像测井成本较高的问题。同时根据神经网络模型诊断得到的裂缝宽度优化堵漏材料的粒径配比，提高了裂缝内的架桥封堵强度和架桥的稳定性，封堵层的承压能力达到12.8 MPa，反向承压能力达到4.5 MPa。现场堵漏试验最高憋压10 MPa，经过封堵作业后大排量循环不漏，达到了裂缝性地层高效堵漏的目的，堵漏一次成功。      

A precise sensor fault detection technique using statistical techniques for wireless body area networks

One of the major challenges in wireless body area networks (WBANs) is sensor fault detection. This paper reports a method for the precise identification of faulty sensors, which should help users identify true medical conditions and reduce the rate of false alarms, thereby improving the quality of services offered by WBANs. The proposed sensor fault detection (SFD) algorithm is based on Pearson correlation coefficients and simple statistical methods. The proposed method identifies strongly correlated parameters using Pearson correlation coefficients, and the proposed SFD algorithm detects faulty sensors. We validated the proposed SFD algorithm using two datasets from the Multiparameter Intelligent Monitoring in Intensive Care database and compared the results to those of existing methods. The time complexity of the proposed algorithm was also compared to that of existing methods. The proposed algorithm achieved high detection rates and low false alarm rates with accuracies of 97.23% and 93.99% for Dataset 1 and Dataset 2, respectively.     

Impact assessment of reservoir desiltation measures for downstream riverbed migration in climate change: A case study in northern Taiwan

Typhoon Aere in 2004 induced severe sedimentation and loss of storage capacity of the Shihmen Reservoir in northern Taiwan. The resulting dramatic increase in the turbidity of the water seriously affected the water supply. To effectively maintain the stability of the water supply and maintain the reservoir’s storage capacity, the government of Taiwan began to plan and construct a series of improvement measures, such as a sediment flushing tunnel, the JhongJhuang Bank-Side Reservoir, and the Amuping Desilting Tunnel. However, previous studies only focused on the impact of the sediment flushing tunnel and the Amuping Desilting Tunnel on the downstream riverbed, and did not consider the possibility of increasing sediment discharge after the completion of the JhongJhuang Bank-Side Reservoir. In addition, climate change will cause the intensity of extreme rainfall to increase enormously in the future. That rainfall and extra sediment flushing will challenge the existing flood prevention facilities. Therefore, this study considered that the JhongJhuang Bank-Side Reservoir will increase sediment discharge of the Shihmen Reservoir, and used dynamical downscaling extreme typhoon data of climate change under the RCP 8.5 scenario to explore the flood prevention and riverbed migration of the main channels of the Dahan and Tamsui Rivers in the future. We used the rainfall–runoff model of Hydrologic Modeling System to simulate rainfall and runoff, and used the hydraulic and sediment transport model of CCHE1D to holistically simulate flood events and consequent river scouring and deposition behaviors. Our results showed that the projected peak discharge during the late 21st century (2075 to 2099) will be at least 50% higher than that during the baseline (1979 to 2003) period. In terms of flood prevention, the potential of overbank flooding will increase in the downstream area, and the trend of long-term change in the riverbed will be dominated by degradation (-0.489 ± 0.743 m) in the future. The improvement measures will have a limited impact on riverbed migration (0.011 ± 0.094 m) in the Dahan and Tamsui Rivers. After the operation of the JhongJhuang Bank-Side Reservoir, the Shihmen Reservoir is expected to increase the sediment discharge ratio by 70% during floods, and it will not cause excessive water turbidity that may affect downstream water supply.     

Impact of the anode operating conditions on the liquid water distribution in the cathode gas diffusion layer

Previous experimental results indicate that the humidification conditions at the anode have an impact on the liquid water distribution in the cathode gas diffusion layer. Numerical simulations are developed to reproduce and analyze this effect. Results consistent with the experimental results are first obtained by playing with the partition coefficients of an advanced pore network model computing the liquid water formation and transfer in the cathode gas diffusion layer (GDL) for a large range of operating conditions. Then, a model for the full anode – cathode assembly is developed by combining the pore network model of the cathode GDL and a 1D model describing the heat and water transfer in the various components of the anode-cathode assembly. This enables one to generalize the dry – wet regime diagram introduced in a previous work by incorporating the effect of the humidity condition at the anode.     

Engineering grain boundary anisotropy to elucidate grain growth behavior in alumina

Current grain growth models have evolved to account for the relationship between grain boundary energy/mobility anisotropy and the five degrees of grain boundary character. However, the role of grain boundary networks on overall growth kinetics remains poorly understood. To experimentally investigate this problem, a highly textured Al₂O₃ was fabricated by colloidal casting in a strong magnetic field to engineer a unique spatial distribution of grain boundary character. Microstructural evolution was quantified and compared to an untextured sample. From this comparison, a prevalence of (0001)/(0001) terminated grain boundaries with anisotropic networks were identified in the textured sample. These boundaries and their networks were found to be driving grain growth at a faster rate than predicted by models. These findings will allow better modelling of grain growth in real systems by experimentally exploring the impact thereon of grain boundary plane anisotropy and relative energy/mobility differences between neighboring boundaries.     

Specific emitter identification for satellite communication using probabilistic neural networks

Electromagnetic signal emitted by satellite communication (satcom) transmitters are used to identify specific individual uplink satcom terminals sharing the common transponder in real environment, which is known as specific emitter identification (SEI) that allows for early indications and warning (I&W) of the targets carrying satcom furnishment and furthermore the real time electromagnetic situation awareness in military operations. In this paper, the authors are the first to propose the identification of specific transmitters of satcom by using probabilistic neural networks (PNN) to reach the goal of target recognition. We have been devoted to the examination by exploring the feasibility of utilizing the Hilbert transform to signal preprocessing, applying the discrete wavelet transform to feature extraction, and employing the PNN to perform the classification of stationary signals. There are a total of 1000 sampling time series with binary phase shift keying (BPSK) modulation originated by five types of satcom transmitters in the test. The established PNNs classifier implements the data testing and finally yields satisfactory accuracy at 8 dB(±1 dB) carrier to noise ratio, which indicates the feasibility of our method, and even the keen insight of its application in military.     

Application of the Microsoft Excel Solver tool in the solution of optimization problems of heat exchanger network systems

Optimization of heat exchanger networks (HEN_S) is a field of interest in Chemical Engineering. The aim is to use the residual heat of process streams to raise the temperature of other process streams which are cold, thus minimizing the use of hot and cold utilities. The usual way to deal with this task is to pose a linear programming problem according to a transshipment model in order to minimize either the general services consumptions or the number of hot and cold stream matchings required. This optimization is subjected to several restrictions given by the energy balances corresponding to each heat exchange.The high number of variables and equations obliges the use of specific software to solve these problems, e.g. GAMS (General Algebraic Modelling System). However, this software is not intuitive and requires a long time of training and a certain level of practice for the students to adequately use it.This work describes the use of Microsoft Excel-Solver for the sequential solving of HEN_S optimization problems according to the transshipment model. Solver is a much simpler, intuitive and easily available tool for the students who, besides, usually learn how to use it in the first years of their degree, in Informatics or similar subjects. Thus, it is not necessary to spend extra time in the teaching of the software, time that may be devoted to other contents.This paper presents an example of HEN_S problem proposed in the subject Simulation and Optimization of Chemical Processes corresponding to the Joint Master in Chemical Engineering of the Rey Juan Carlos University and the Autónoma University of Madrid and solved by the students using Excel-Solver.