Novel approach in investigation of the poly(acrylic acid) hydrogel swelling kinetics in water

The swelling kinetics curves of structurally defined poly(acrylic acid) hydrogel in bidistilled water at temperatures: 25, 30, 35, 40, and 45°C were determined. The possibility of kinetically explaining the isothermal swelling process by applying the following models: reaction controlled by diffusion, first order chemical reaction kinetics, and second order chemical reaction kinetics, was investigated. It was found that kinetically explaining the swelling process using these methods was limited to only certain parts of the process. The swelling process in bidistilled water was described in full range assuming that the hydrogel's swelling rate was a kinetically controlled reaction by the rate of the movement of reactive interface of hydrogel. Based on that model, the kinetic parameters, activation energy (E_a) and preexponential factor (A), of the swelling process were determined to be E_a = 35 kJ/mol and lnA = 8.6. A possible mechanism of the investigated swelling process was discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

CX6112车铣复合机床设计方案的研究与探讨

文章较系统地论述了车铣复合机床设计方案的形成过程，同时分析了该设计方案的持点，并简要介绍了该产品的主要技术参数和用途，简评了该产品的技术水平。     

厅堂音质评价参量的相关性分析

当代室内声学专家经常选用的评价厅堂音质的物理参量，其间有几个量是相关的。作为室内音质设计的依据．必须寻找基本相互独立的参量，才有更大的实用意义。     

MC^2电缆介质结构及阻抗分析

本文将用数学和实验两种方法证实MC～2电缆不仅能保证特性阻抗变化不超出电缆技术规范。而且能保证在设计频率范围内电缆结构反射损耗最小。     

多面体含能材料的爆速和爆压预估

当采用R-P经验方法预估多硝基笼状化合物最大理论密度下爆速和爆压时,需要修正F因子中与分子结构有关的A/3项,使F因子包含有来自笼状分子高晶体密度和分子内部高张力能的贡献。与K-J方法相比,改进R-P方法既保持了原式的优点,又使预估结果获得明显改善。把K-J方法预估结果作为基础数据,利用改进R-P方法估算25种多硝基笼状化合物的爆速和爆压,结果表明该方法的相对误差分别为±1.9％和±5.2％。而用R-P方法时,预估爆速和爆压的相对误差分别为±14.0％和±21.4％。     

一种按时间切换的最速控制方法

基于初始状态空间下的子空间概念，提出了一种按时间进行切换的最速控制方法，不需要求取开关线或开关面。数字仿真结果表明，采用这一方法是完全可行的。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Plasma properties of laser-ablated St target in air

Ｐｌａｓｍａｐｒｏｐｅｒｔｉｅｓｏｆｌａｓｅｒ－ａｂｌａｔｅｄＳｔｔａｒｇｅｔｉｎａｉｒＷａｎｇＸｉａｎｇ－Ｔａｉ（王象泰）；ＭａｎＢａｏ－Ｙｕａｎ（满宝元）；ＷａｎｇＧｏｎｇ－Ｔａｎｇ（王公堂）；ＦａｎＸｉ－Ｊｕｎ（樊锡君）；ＷａｎｇＪｕｎ（王军）...     

感应电动机转速对定子电流暂态过程的影响

本文运用根轨迹法，分析了感应电动机转速对定子电流暂态过程的影响。并通过对稳态时定子电流在电压阶跃干扰下的暂太响应分析，验证了结论有效性。     

气门用4Cr9Si2钢调质工艺研究

采用正交试验 ,研究了 4Cr9Si2钢的淬火温度、回火温度与组织、硬度间的关系 ,得出了最佳的工艺参数 (10 10℃淬火 ,6 0 0℃回火 )。实际生产表明 ,采用此工艺后 ,断裂现象基本消除 ,气门的热处理质量有了明显提高。