CX6112车铣复合机床设计方案的研究与探讨

文章较系统地论述了车铣复合机床设计方案的形成过程，同时分析了该设计方案的持点，并简要介绍了该产品的主要技术参数和用途，简评了该产品的技术水平。     

厅堂音质评价参量的相关性分析

当代室内声学专家经常选用的评价厅堂音质的物理参量，其间有几个量是相关的。作为室内音质设计的依据．必须寻找基本相互独立的参量，才有更大的实用意义。     

MC^2电缆介质结构及阻抗分析

本文将用数学和实验两种方法证实MC～2电缆不仅能保证特性阻抗变化不超出电缆技术规范。而且能保证在设计频率范围内电缆结构反射损耗最小。     

一种按时间切换的最速控制方法

基于初始状态空间下的子空间概念，提出了一种按时间进行切换的最速控制方法，不需要求取开关线或开关面。数字仿真结果表明，采用这一方法是完全可行的。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Plasma properties of laser-ablated St target in air

Ｐｌａｓｍａｐｒｏｐｅｒｔｉｅｓｏｆｌａｓｅｒ－ａｂｌａｔｅｄＳｔｔａｒｇｅｔｉｎａｉｒＷａｎｇＸｉａｎｇ－Ｔａｉ（王象泰）；ＭａｎＢａｏ－Ｙｕａｎ（满宝元）；ＷａｎｇＧｏｎｇ－Ｔａｎｇ（王公堂）；ＦａｎＸｉ－Ｊｕｎ（樊锡君）；ＷａｎｇＪｕｎ（王军）...     

感应电动机转速对定子电流暂态过程的影响

本文运用根轨迹法，分析了感应电动机转速对定子电流暂态过程的影响。并通过对稳态时定子电流在电压阶跃干扰下的暂太响应分析，验证了结论有效性。     

气门用4Cr9Si2钢调质工艺研究

采用正交试验 ,研究了 4Cr9Si2钢的淬火温度、回火温度与组织、硬度间的关系 ,得出了最佳的工艺参数 (10 10℃淬火 ,6 0 0℃回火 )。实际生产表明 ,采用此工艺后 ,断裂现象基本消除 ,气门的热处理质量有了明显提高。     

利用光纤数字同步传送网2.048 Mbit/s支路传送高精度标准时间信号

首次提出一种利用光同步数字传送网的2.048Mbit/s信号传送高精度时间编码信号的方法和实验结果。它可以使整个通信网的交换机、计费系统、网管系统、基站控制器等设备实现与UTC的时间同步。目前的实验证明,时间同步的不确定度优于±5μs。     

Viscous behaviour of glass-forming liquids: a thermodynamic approach

The temperature dependence of the viscosity of the undercooled melts exhibits an important role in the study of nucleation, crystal growth and the glass-forming ability of materials. Several attempts have been made to study the viscous behaviour of the glass-forming melts and these investigations are mainly based on free volume theory as well as on the configurational entropy model. In the present investigation, an attempt has been made to correlate the thermodynamic parameters with the viscosity of the glass-forming melts and to study the temperature dependence of the viscosity of undercooled liquids on the basis of the free volume theory as well as on the basis of the configurational entropy model of Adam and Gibbs. The entire study is confined on the expression for thermodynamic parameters reported by the authors recently. The expression obtained has been successfully applied to study the temperature dependence of the viscosity of the metallic, molecular and oxide glass-forming liquids.