IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

溶剂萃取分离锂同位素研究Ⅱ.苏丹Ⅰ-中性配位体协萃体系萃取分离锂同位素效应探讨

文章讨论了苏丹I-中性配位体协萃体系萃取分离锂同位素中螯合剂和协萃剂的结构效应。为了获得高的同位素分离效应,螯合剂必须是弱酸性的(PK_α>11),具有强的分子内氢键及易于形成六元螯合环。协萃剂结构不仅要求无空间位阻,而且具有强的配位基。α随配位基的碱性增大而相应提高。萃取络合物中螯合环的增多亦有利于体系α的提高。此外本文还讨论了一些萃取体系的同位素富集方向和萃锂体系用于分离同位素的前景。     

"Does reward increase or decrease creativity?": Correction to Eisenberger and Selbst.

Reports an error in "Does reward increase or decrease creativity" by Robert Eisenberger and Michael Selbst (Journal of Personality and Social Psychology, 1994[Jun], Vol 66[6], 1116-1127). In the aforementioned article, Figures 1 and 2 were interchanged. The figures appear with their correct captions in the erratum. (The following abstract of the original article appeared in record 1994-40652-001.) Two studies involving 504 school children investigated why behaviorists and cognitively oriented investigators have come to opposite conclusions about reward's effects on creativity. A monetary reward for a high degree of divergent thought in 1 task (word construction) increased children's subsequent originality in a different task (picture drawing). The same reward, made contingent on a low degree of divergent thought, reduced this generalized originality. These effects were eliminated by using a large reward and were restored by keeping the large reward out of the children's sight. The results suggest that reward training increases generalized creativity when (1) a high degree of divergent thought is required and (2) the reward is presented in not too salient a fashion. The findings are consistent with a 2-factor interpretation of rewarded creativity effects that incorporates learned industriousness and selective attention. [A correction concerning this article appears in Journal of Personality & Social Psychology, 1994(Jul), Vol 67(1), 125. Figures 1 and 2 were interchanged.] (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.