Influence of adsorption on the measurement of diffusion coefficients by Taylor dispersion

The effect of adsorption on the measurement of diffusion coefficients by the Taylor dispersion technique is investigated by modifying the governing equation to account for reversible, nonequilibrium adsorption. The resulting two-dimensional equations are solved by an explicit finite-difference technique. Experimental data for the acridine carbon dioxide system indicated that acridine adsorbs on the walls on the tubing and these data were investigated with this model. The influence of carious parameters including the number of sites and the rates of adsorption desorption was investigated by conducting a parametric sensitivity analysis on the model. It was found that adsorption of the solute on the wall of the tubing could produce an error as high as 35% on the measured diffusion coefficient compared to the actual diffusion coellicient. Examination of the influence of each of the parameters will enable Inure investigators to reduce the effect of adsorption in the measurement of diffusion coefficients by Taylor dispersion.     

TiO_2载体表面酸性的研究

利用NH_3吸附和吡啶吸附红外技术研究TiO_2的制备条件对其表面酸性的影响。结果表明,用NH_3水中和TiCl_4溶液方法制备的TiO_2(A)表面有较强的L酸中心,中和条件对表面酸性中心数目和强度有显著影响。由TiOSO_4水解方法制备的TiO_2(B)表面具有较强的L酸中心和较弱的B酸中心,引入不同添加剂可有效地调变TiO_2载体表面的酸性。     

气相色谱在线分析变压吸附法制纯氢中的总碳

利用带镍加氢转化炉的气相色谱仪 ,在线分析变压吸附法制纯氢中的总碳。该法用变压吸附法制的纯氢作燃气 ,在检测器前端将氢气中的CO和CO2 转化为CH4,然后用氢火焰离子化检测器检测 ,直接以检测器的信号 (mV)进行定量。当氢气中总碳体积分数在 1 9～ 5 0 0 μl/L时 ,FID信号值与总碳体积分数有良好的线性关系。方法回收率为 99 90 %～ 10 1 9%,相对标准偏差 <1%。     

高温高压下多种气体在储层岩心中吸附等温线的测定

利用自行研制的XF1型高温高压气体吸脱附测试仪,结合一台色谱分析仪(HP6890),一套抽真空系统,分别测定了N₂、CH₄、C₂H₆、C₃H₈、nC₄及其混合气体在三个岩心中的吸脱附等温线共计42条(单组分30条,累计测试点516个;混合气12条,累计测试点203个),以及吸附平衡后混合气的自由气相组成、吸附相组成和各组分的吸附等温线各48条(累计测试点431个).测试的温度为50.5℃.实验结果表明:①储层岩心介质对烃类气体的吸附现象是客观存在的,不容忽视;②仅就测试所得的数据来看,如果忽略其它因素,可以初步估计,不考虑吸附的砂岩储层气藏的计算储量将比考虑吸附少5%以上;③岩心-气体吸附体系的吸附能力除受压力影响外,更受到储层介质、岩石成分、结构和物性性质的影响,除此之外,还受到多组分气体中重烃组分数目、摩尔含量等的影响;④多组分气体组分相对吸附量能有效地表征多组分气体中各组分气体的竞争吸附能力大小,依据这个指标可将五元多组分气体体系中各组分气体按其竞争吸附能力由强到弱排序为nC₄>C₃H₈>C₂H₆>CH₄>N₂.     

Isotherm analyses for single component and multi-component metal sorption onto lignite

The adsorption of the three metal ions, copper, cadmium and zinc in single component and multi-component mixtures in aqueous solutions by lignite is reported. A comparison is made between the single component saturation uptake and the multi-component uptakes. The isotherms indicate a competitive uptake with copper being preferentially absorbed by the lignite in multi-component solutions. The isotherms are plotted to obtain the Langmuir constants, the Freundlich constants and the Redlich–Peterson constants. Lignite is shown to possess an affinity for the metal ions which make its use as an adsorbent a possible alternative to the use of more expensive activated carbons.     

Dispersion—flocculation studies on a Goethite-clay system

Dispersion–flocculation studies on a Goethite–clay system using flocculants were carried out as a function of flocculant concentrations, pH of slurry, time of agitation and dispersant dosage. Also, the effects of pH and polymer concentrations on the adsorption behaviour of the system were investigated. Results show that well flocculated goethite was preferentially obtained from 4% goethite/kaolinite clay suspensions, with 50 ppm causticised starch in the slurry at pH values of 3–11·5 and with 50 ppm polyacrylamide at pH values of 3–8. Good flocs were also obtained on flocculation of the goethite suspension with 50 ppm polyacrylamide at pH values of 5–7, while the kaolinite suspension did not respond to the same dosage of causticised starch in the same pH range. Results further reveal that for the goethite/kaolinite suspension, the best results was obtained with 50 ppm polyacrylamide at pH values of 7–10. Based on the data generated in the study, it was concluded that causticised starch is a better flocculant than polyacrylamide for goethite suspensions although polyacrylamide is an excellent flocculant for kaolinite suspensions.     

Recovery of pyruvic acid with weakly basic polymeric sorbents

BACKGROUND: Carboxylic acids are among the most important substances that can be manufactured from biomass. However, the recovery of carboxylic acids from fermentation broths presents a challenging separation problem. To avoid the production of waste salts and net consumption of chemicals in the calcium carboxylate salt process, the use of reversible chemical complexation with polymeric sorbents and extractants is attractive for carboxylic acid recovery. Pyruvic acid is widely used in the manufacture of medicines, pesticides and foodstuffs and can be produced by fermentation. Since the acidity of pyruvic acid (pK_a = 2.49) is stronger than that of normal carboxylic acids, and as few reports on the recovery of pyruvic acid are available, the sorption of pyruvic acid from aqueous solution on two types of weakly basic polymeric sorbent, tertiary amine D301R and primary amine D392, was investigated over a wide pH range and at various salt (MgSO₄) concentrations. RESULTS: Overloading adsorption of pyruvic acid on both weakly basic polymeric sorbents occurred, with the overloading of D392 being greater than that of D301R. The adsorption of pyruvic acid on both sorbents was greatly affected by the solution pH and the salt concentration in the aqueous phase. An overloading model was able to predict the experimental uptake data very well. CONCLUSION: Solution pH is one of the most important operating conditions, and both polymeric sorbents D392 and D301R can be used to recover pyruvic acid from dilute aqueous solution with high efficiency at a solution pH around 2. The uptake by D392 is greater than that by D301R owing to steric hindrance of the tertiary amine. Copyright © 2008 Society of Chemical Industry     

Synthesis,extraction, and adsorption properties of calix[4]arene‐poly(ethylene‐glycol) crosslinked polymer

Novel calix[4]arene‐poly(ethylene glycol) crosslinked polymer (CCP) has been synthesized by the polycondensation reaction between a p‐tert‐butylcalix[4]arene derivative and dihydroxyl capped poly(ethylene glycol) (DHPEG, M_n = 1000) catalyzed by neodymium tosylate. The hydrogel, consisted of 66.9% water and 33.1% CCP, can selectively extract aromatic organic molecules from aqueous solution according to the diameter of the guest molecules, which infers that the diameter of the calix[4]arene cavity is about 5.4 Å and the conformation of calix[4]arene units altered from cone conformation to 1,3‐alternate conformation during the polycondensation reaction. Furthermore, CCP can also adsorb naphthalene from gas phase, showing much higher capacity than active carbon does, which may have some potential applications in the field of separation and environment protection. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Surface adsorption of comb polymers by Monte Carlo simulations

This paper reports off-lattice Monte Carlo simulations of highly-branched comb homopolymers weakly adsorbed on a flat, featureless surface showing only covolume and dispersion interactions with the adsorbate. A minimal coarse-grained model, described by hard spheres connected by harmonic springs, was employed. The interaction energy of the adsorbed combs and linear chains is first discussed as a function of the molecular mass and of the number of beads in contact with the surface. The molecular size is then investigated as a function of backbone length and branching density at a fixed arm size. The apparent swelling exponents of the adsorbed combs are larger than those of the corresponding linear chains, and much larger than that of the free molecules. This result indicates a surface-induced stiffening of the comb backbone, further studied through the persistence length l_pers. It is found that l_pers increases upon adsorption over the free-molecule value, more so the larger is the branching density. Finally, the thickness of the adsorbed layer, the surface-induced molecular anisotropy and the molecular aspect ratio are investigated as a function of branching density and molecular mass.     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.