Thermal stability behaviors of Cr(N,O)/CrN double-layered coatings by TGA/DTA analysis

In this study, Cr(N,O)/CrN double-layered coatings were synthesized using the cathodic arc deposition (CAD) process. CrN film was first deposited onto a substrate as an interlayer to ensure better adhesion, and Cr(N,O) film was subsequently deposited on top of the CrN layer as the surface layer. Variation in the Cr(N,O) coating composition was achieved through changing the O₂/N₂ flow ratio during the last stage of processing. Phase structure, chemical composition, and morphology of the resulting coatings were analyzed and observed using the X-ray diffractometer, Auger electron spectrometer and SEM. In addition, oxidation behavior of the coatings was investigated using TGA/DTA methods. The tests were carried out by increasing temperature up to 1000 °C in ambient air. With the introduction of oxygen gas during the CAD process, a superficial layer was produced in the Cr(N,O) constituent containing CrN and Cr₂O₃ phases. The formation of the oxide phase attributed to the reaction of chromium and oxygen was more favorable than that of chromium and nitrogen. The results also showed that Cr(N,O)/CrN double-layered coatings exhibited superior oxidation resistance at elevated temperature than that of CrN single-layer coated specimen (870 °C vs. 750 °C).     

液压-齿轮-齿条圆弧分型抽芯压铸模设计

给出了龙头体液压-齿轮-齿条圆弧分型抽芯压铸模实用结构，论述了模具的浇铸系统、结构特点和工作原理。该模具采用扇形龄轮-齿条机构实现龙头体铸件的侧向圆弧分型抽芯，同时通过相应的两套斜销滑块机构分别实现龙头体铸件另外两个方向的侧向分型抽芯。     

单片机系统在焊接控制器中的应用

介绍2种单片机焊接控制器的功能参数及设计思路。一种采用80C196KB PSD311的16位总线结构；另一种采用89C52的8位总线结构。实践证明单片机系统是焊接设备中比较理想的控制器件。     

化学冶金因素对埋弧焊焊缝硫磷含量的影响

通过试验和理论分析，探讨了在埋弧焊过程中，熔池中Ｓ，Ｐ的脱去过程，主要是以分别生成硫酸盐和磷酸盐的形式进行的化学冶金反应，并提出了熔池中的硫，磷脱去过程存在一个极限值，而这个极限值与焊剂的碱度和焊剂，焊丝及母材中的硫，磷含量有关。在焊剂碱度ＢＩ≥２．５的高碱度焊剂中，根据焊丝或焊剂中硫含量的不同，熔敷金属中硫的的极限值可低于焊丝中的硫含量或接近焊剂中的硫含量；而磷的极限值为０．０１０％±０．００２     

钛及钛合金电弧钎焊及接头强度

用Ti—Cu—Ni，Ti-Cr-Zr钎料在TIG电弧加热条件对TA2和Ti—6Al—4V钛合金进行钎焊。结果表明：用Ti—Cu—Ni钎料钎焊TA2和Ti—6Al—4V钛合金的搭接接头强度分别是418．3MPa和439．6MPa；用Ti—Cr—Zr钎料钎焊TA2和Ti—6Al—4V钛合金的搭接接头强度分别是575．2MPa和656．1MPa。对Ti-Cu-Ni钎料／母材界面分析认为固液异分化合物η相((Cu，Ni)Ti2)生成时呈笋状生长，嵌入钎缝对钎缝的强度提高有利。对Ti-Cr-Zr钎料／母材界面分析，认为主要是固溶体β-Ti(Cr)存在提高了钎缝强度。     

波形控制逆变CO2焊接电源关键控制信号的获取

通过分析波形控制CO2焊接过程，介绍了焊接电源空载、燃弧、短路等工作状态的判别，电流、电压、du/dt、di/dt等关键信号的获取方法，为研制波形控制CO2逆变焊机奠定了基础。     

国内弧焊设备电磁兼容性研究进展

焊弧设备的电磁兼容性问题日益突出，受到越来越多的关注。针对我国的实际情况，对国内弧焊设备的研究现状进行了综合分析，同时指出了今后的研究方向。     

埋弧焊机的单片机控制系统设计

设计了以MCS-51单片机为控制核心的埋弧焊机控制系统．实现焊接过程的实时控制，保证了焊接电流和电弧电压的自动调节。通过实际生产应用表明：该控制系统工作稳定可靠，焊接质量较好，能够满足生产要求。     

气体保护焊在变压器波纹油箱制造中的应用

简述了变压器波纹油箱的结构和焊接方法，通过纯CO2和混合气体2种焊接工艺方法的实践，肯定了混合气体保护焊应用于变压器波纹油箱焊接工艺是切实可行的，具有推广使用价值。