Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

基于三维胞元空间的MA双向并行路由算法

针对传统移动代理(MA)在监测无线传感器网络(WSNs)的感兴趣信息时产生的延迟较大和能耗较多问题,提出了基于三维胞元空间的MA双向并行(3D-BPMA)路由算法.3D-BPMA将MA与传统的客户/服务器(c/S)模式相结合,在胞元内利用C/S模式搜集信息,在单层胞元系统和路由器与路由器之间采用MA双向并行的策略进行传输.仿真结果表明:3D-BPMA与LCF,DSG-MIP算法相比减少了平均响应时间和网络平均能耗,提高了MA发送率.     

Coil‐Type Asymmetric Supercapacitor Electrical Cables

Cable‐shaped supercapacitors (SCs) have recently aroused significant attention due to their attractive properties such as small size, lightweight, and bendability. Current cable‐shaped SCs have symmetric device configuration. However, if an asymmetric design is used in cable‐shaped supercapacitors, they would become more attractive due to broader cell operation voltages, which results in higher energy densities. Here, a novel coil‐type asymmetric supercapacitor electrical cable (CASEC) is reported with enhanced cell operation voltage and extraordinary mechanical‐electrochemical stability. The CASECs show excellent charge–discharge profiles, extraordinary rate capability (95.4%), high energy density (0.85 mWh cm⁻³), remarkable flexibility and bendability, and superior bending cycle stability (≈93.0% after 4000 cycles at different bending states). In addition, the CASECs not only exhibit the capability to store energy but also to transmit electricity simultaneously and independently. The integrated electrical conduction and storage capability of CASECS offer many potential applications in solar energy storage and electronic gadgets.     

Macroscopic and Microscopic Structures of Cesium Lead Iodide Perovskite from Atomistic Simulations

A first‐principles‐based effective Hamiltonian is developed and employed to investigate finite‐temperature structural properties of a prototype of perovskite halides, that is CsPbI₃. Such simulations, when using first‐principles‐extracted coefficients, successfully reproduce the existence of an orthorhombic Pnma state and its iodine octahedral tilting angles around room temperature. However, they also yield a direct transformation from Pnma to cubic $Pm\overline{3}m$ upon heating, unlike measurements that reported the occurrence of an intermediate long‐range‐tilted tetragonal P4/mbm phase in‐between the orthorhombic and cubic phases. Such disagreement, which may cast some doubts about the extent to which first‐principle methods can be trusted to mimic hybrid perovskites, can be resolved by “only” changing one short‐range tilting parameter in the whole set of effective Hamiltonian coefficients. In such a case, some reasonable values of this specific parameter result in the predictions that i) the intermediate P4/mbm state originates from fluctuations over many different tilted states; and ii) the cubic $Pm\overline{3}m$ phase is highly locally distorted and develops strong transverse antiphase correlation between first‐nearest neighbor iodine octahedral tiltings, before undergoing a phase transition to P4/mbm under cooling.     

Reduction of waste biosolids by RAS-ozonation: Model validation and sensitivity analysis for biosolids reduction and nitrification

Biosolids reduction model by return activated sludge ozonation was validated by simulating nitrification data compiled from our pilot-scale and the literature studies. Then, a global sensitivity analysis (GSA) was performed to identify influential and non-influential parameters for biosolids reduction efficiency, change in specific nitrification activity (SNA), and alteration to expected nitrification stability. In general, the model outputs were sensitive to operational and ozone reaction parameters, but not to biochemical parameters. For operational parameters, mainly temperature and initial solids retention time (SRT) influenced all model outputs. For biosolids reduction, increase in the degradability of the influent COD decreased the reduction efficiency. For SNA, the changes were highly dependent on the influent TKN/COD ratio. Our findings also imply that the stability of the nitrification process in ozonated systems should be enhanced at constant MLVSS for warm temperatures, but could be reduced at temperatures below 12 °C and aerated SRTs below 10 days.     

Molecular structure and granule morphology of native and heat‐moisture‐treated pinhão starch

Pinhão seed is an unconventional source of starch and the pines grow up in native forests of southern Latin America. In this study, pinhão starch was adjusted at 15, 20 and 25% moisture content and heated to 100, 110 and 120 °C for 1 h. A decrease in λ max (starch/iodine complex) was observed as a result of increase in temperature and moisture content of HMT. The ratio of crystalline to amorphous phase in pinhão starch was determined via Fourier transform infra red by taking 1045/1022 band ratio. A decrease in crystallinity occurred as a result of HMT. Polarised light microscopy indicated a loss of birefringence of starch granules under 120 °C at 25% moisture content. Granule size distribution was further confirmed via scanning electron microscopy which showed the HMT effects. These results increased the understanding on molecular and structural properties of HMT pinhão starch and broadened its food and nonfood industrial applications.     

Effect of gums on viability and β‐galactosidase activity of Lactobacillus spp. in milk drink during refrigerated storage

The viability and β‐galactosidase activity of four Lactobacillus strains in milk drink containing gums during 28 days of refrigerated storage at 4 °C were assessed. The population of Lactobacillus rhamnosus GGB101 and Lactobacillus rhamnosus GGB103 were maintained, whereas the population of Lactobacillus reuteri DSM20016 and Lactobacillus reuteri SD2112 significantly decreased. The recommended level of 6 log CFU g^?1 was exceeded for all tested trains throughout storage. The highest viable number of Lactobacillus rhamnosus GGB103 (8.76 ± 0.03 log CFU mL^?1) was obtained in the product containing carrageenan–maltodextrin. The addition of guar–locust bean–carrageenan led to 20‐fold increase in the level of β‐galactosidase activity for L. rhamnosus GGB101 (1208 ± 2.12 Miller units mL^?1) compared to the control (61 ± 2.83 Miller units mL^?1). Our results suggested that gums could be added to milk to improve viability and enhance β‐galactosidase activity of Lactobacillus.