Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Electrostatic destabilization of water-in-crude oil emulsions: Application to a real case and evaluation of the Aibel VIEC technology

In the current study, the Aibel Vessel Internal Electrostatic Coalescer (VIEC) technology was tested for a real case scenario encountered in the production train of a UK oil field. Depressurized samples were collected both upstream and downstream of the first stage separator. The separation performance was discussed with respect to water cut and droplet size distribution of the emulsions, and the effect of chemical treatment. Issues with respect to representative sampling and testing have been discussed. The application of an external AC electrical field has been shown to significantly enhance the separation of the aqueous phase from tight emulsions, both when it was used alone and in combination with a commercial demulsifier. By using the VIEC technology, the time for separation could be reduced from 8 min to 2 min and the overall BS&W in the emulsions was improved from 45% or 60% to a residual water content of 5-20%. Destabilization of a 45% water-in-oil emulsion by electrical and chemical treatment (20/40 ppm) produced oil in the 2-7% BS&W range whereas the corresponding tests without applying an electrostatic field led to a BS&W greater than 25%. The achieved results strongly suggest that the VIEC technology can resolve the stable emulsion bands encountered in the Schiehallion train and add flexibility or increased production rate to the process. The results also suggest the importance of further studies on the destabilization performances achieved by electrostatic means.     

Influence of the amount of ferromagnetic addition on the rheological properties of spinning solutions,the structure,the strength,and thermal properties of polyacrylonitrile fibres

The rheological properties of spinning solutions of polyacrylonitrile in dimethyl formamide (DMF) containing various amounts of a ferromagnetic nanoaddition were investigated. The porous structure, the strength and thermal properties of fibers obtained from these solutions were assessed, as well as the uniformity of the nanoaddition distribution on the fiber surface was estimated. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Effect of olive residue benzylation on the thermal and mechanical properties of poly(vinyl chloride)/olive residue composites

The changes in mechanical properties, the thermal stability, and the water absorption capacity of poly (vinyl chloride)/olive residue flour composites were studied as a function of various residue olive flour ratios, i.e., 0, 5, 15, and 25% by weight taking into account the effect of benzylation chemical treatment of the filler. The study showed that composite samples prepared with the untreated filler exhibited higher tensile modulus and hardness compared with the neat resin, whereas elongation and tensile strength were observed to decline. On the other hand, the PVC hardness was found to increase with addition of the untreated olive residue flour (ORF), however the composite samples prepared with the benzylated flour exhibited lower hardness than those prepared with untreated olive residue. Moreover, the amount of absorbed water depends on the amount of filler in the composite. The comparison of the results obtained from the samples of F5, F20, and F30 formulations between the untreated and treated ORF indicated a reduction in absorbed water for the composite samples containing treated ORF with benzyl chloride. As a result, the mechanical properties of the treated composites were improved. Furthermore, the thermal characterization of the different samples carried out by color change test and thermogravimetric analysis revealed an increase in the onset temperatures of decomposition for the treated composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Studies on jute–asphalt composites

The tensile properties of jute make it a suitable raw material for asphalt overlay (A/O) fabric. In this study, the thermal stability of jute under conditions of asphalt overlaying process was investigated and the compatibility of jute with asphalt was assessed through experimentation on jute–asphalt composites under mechanical and hygral loads. Fourier transform infra red (FTIR) spectroscopic study revealed probable chemical bonding between jute and asphalt. The test for ascertaining the capability of asphalt encasement for protecting jute against biodegradation under enzymatic attack was found positive. A 6‐month hygral treatment, of the jute–asphalt composite, showed significant increase in modulus of the material. The results indicate that although the strength of jute deteriorates by about 10% under asphalt overlaying condition, the overall tensile behavior of jute fabric–asphalt composite material is considerably superior to that of the pure jute fabric, even under biological and extended hygral loading conditions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

ROI-based Watermarking Scheme for JPEG 2000

A new region of interest (ROI)-based watermarking method for JPEG 2000 is presented. The watermark is embedded into the host image based on the characteristics of the ROI to protect rights to the images. This scheme integrates the watermarking process with JPEG 2000 compression procedures. Experimental results have demonstrated that the proposed watermark technique successfully survives JPEG 2000 compression, progressive transmission, and principal attacks.     

谈谈职业教育的大众性

对职业教育的大众性问题进行了论述、实证分析和理论、政策、改革等思考。     

Fire performance of wood (Pinus radiata) treated with fire retardants and a wood preservative

In this work, we co‐formulated an oil‐borne copper naphthenate/permethrin wood preservative system with synthetic polymer‐based fire‐retardant additives prior to the impregnation of Pinus radiata sapwood. We evaluated what effect, if any, the preservative had upon the fire performance properties of the fire retardants and whether the fire retardants impacted on the fungicidal and termiticidal efficacy of the preservative. The fire retardants included halogenated and phosphorus‐based systems. A mass loss calorimeter, in conjunction with a thermopile, was used to measure the time to ignition and the peak heat release rate (PHRR) from which the fire performance index (FPI) was determined. The preservative properties were evaluated using termite and soil‐block decay bioassays. In summary, we found that the rate of fire growth was reduced when the fire retardants were used in combination with the wood preservative. We also found that the PHRR was a better determinant of fire performance than the FPI. The performance of the wood preservative was enhanced against fungal decay and termite attack when used in combination with the fire retardants. The fire retardants also demonstrated some wood preservative properties of their own. Copyright © 2008 John Wiley & Sons, Ltd.