Production Equations for Unsteady-State Construction Processes

The production equation called Little’s law has been applied to construction data recently. However, Little’s law was derived for steady-state conditions assuming constant input and output rates and long production runs. Production in construction is inherently temporary, and learning curves and environmental influences often render input and output rates unequal and nonlinear. Starting with a conservation of mass formulation, general equations for work-in-process and cycle time for unsteady-state conditions and limited run production are developed. The motivation behind these equations is to explain common trends in production variables seen on construction projects. Previous studies have shown that when output from a construction production system is drastically increased, a significant upward impact is also seen on cycle time and work-in-process, and this work provides underlying theory and equations to explain these trends. Cycle time and work-in-process equations are presented as functions of time and on average. Data from construction activities are used to show that unsteady-state conditions commonly occur. Reasonable simplifications of the general equations provide guidelines for buffer sizing and resource allocation decisions.     

History of Construction, Engineering, and Management in the Department of Civil and Environmental Engineering at Penn State

At Penn State, the credit for broadening the Civil Engineering Department’s longstanding academic focus on analysis and design to include the construction phase must go to Dr. Harmer A. Weeden and his longtime associate Dr. Thomas D. Larson. Jack H. Willenbrock joined the Department as an Instructor in June 1968 and grew the construction program so that today about a fourth to a third of the civil undergraduates obtain employment in the construction industry. The program has awarded about 250 postbaccalaureate degrees.     

Pretreatment of Highly Polluted Pharmaceutical Waste Broth by Wet Air Oxidation

The preoxidation of a highly polluted waste pharmaceutical fermentation broth using wet air oxidation (WAO) has been studied as a possible method for the effective removal of organics. The applied (pre)treatment method should enhance the biotreatability of the pharmaceutical fermentation broth in terms of reduced initial toxicity and higher biodegradability. Preliminary experiments in the pilot biological treatment plant were successful only at low organic loads, whereas the system collapses at higher ones. The characterization of the fermentation broth was started by common physicochemical analysis, whereas several bioassays were used to determine its impact on biological treatment plants and the environment. Toxicity prior to and after WAO was determined using the acute Vibrio fischeri test, measurement of inhibition of O2 consumption, and the Daphnia magna acute test. Ready biodegradability of the treated and untreated broth has also been assessed. WAO experiments were accomplished in the 2?L batch reactor at different temperatures (240/280°C) and operating pressures. WAO experiments confirmed reduction of the toxicity toward microorganisms, whereas oxidized wastewater was more toxic to daphnids. Biodegradability of the oxidized broth has also been enhanced. Further work has been focused on designing appropriate combination of WAO and biological processes.     

Off-Site Exposure to Respirable Aerosols Produced during the Disk-Incorporation of Class B Biosolids

Field experiments were conducted at a Class B biosolids land application site in central Arizona to measure, model, and source-track the off-site transport of aerosols emitted when biosolids were disk-incorporated into soils. Real-time PM10 monitoring provided time-resolved aerosol information sufficient for verifying both off-site concentration and off-site exposure time model results. Under the conditions considered and at a distance of 165?m from the aerosol source, biosolids disk-incorporation resulted in an intermittent exposure to biosolids-derived aerosol concentration between 15 and 40?μg/m3 and an inhalable biosolids dose between 2 and 8?μg. Transport modeling predicted that these doses will decrease with increasing wind speed. In addition, three DNA sequence-based biosolids source tracking methods were applied to aerosol samples and confirmed the presence of biosolids in aerosols at 5, 65, and 165?m from the aerosol source. Field measurements and modeling indicate that the nature of biosolids-derived aerosol exposure is a series of intermittent high concentration puffs, rather than a continuous low concentration.     

AssetCollector: a system for managing collections of cultural assets

In this paper, AssetCollector is presented, which is a system for managing collections of cultural assets. AssetCollector covers the needs of collection curators towards defining, populating and searching a collection in a flexible way, while supporting them in generating reports based on the collection’s assets and reusing them in order to build web sites and CD-ROMs. In order to support the above functionality, the system provides the content structuring subsystem, the content input subsystem, the search subsystem and the report subsystem. The use of the subsystems is straightforward and requires no technical skills from the curators. AssetCollector has been successfully applied for organizing various collections of cultural assets in Greece, such as archaeological sites, museums and published books. In the future, an evaluation procedure is planned in order to further refine the use of the system according to the targeted users’ needs. Furthermore, more import and export facilities will be provided, which will make the system compliant with widely accepted standards.     

Centum-CS3000系统在PVC聚合装置上的应用

介绍了70m^3悬浮法PVC聚合生产工艺的特点、控制的要求，以及Centum—CS3000系统在该生产装置上的应用。主要讨论了系统配置、组态、控制方案和配方管理。     

持续改进求真务实--记宝钢机械厂导入ISO9000质量管理体系标准实绩

简单介绍了宝钢机械厂贯标经验.     

河北冶金实验厂8MN快锻液压机电控系统选择

着重阐述了河北冶金实验厂８ＭＮ快锻液压机电控系统的选择过程。经过反复考察，论证，对比，最终所选的压机电控系统为目前国产快锻液压机中自动化水平最高的锻造设备。     

ATM网络的可用比特率业务

本文介绍了可用比特率业务的业务特点，速率控制机制以及该业务存在的问题。     

基于TMN的接入网网管系统模型

本文介绍了 TMN 网管系统的体系结构,进而讨论了接入网网管系统的体系结构和管理接口的有关问题。