Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

核电材料在模拟反应堆环境中应力腐蚀破裂测试技术与性能评价

简要介绍了采用慢应变速率试验，Ｕ型弯曲和Ｃ形环试验等技术，分别对８００合金，３０４和３１６及３１６Ｔｉ不锈钢Ａ５３３Ｂ压力容器用多在模拟核反应堆环境中的应力腐蚀破裂敏感性性进行的试验研究的一些主要结果；并结合电化学测试和表面膜俄歇电子能谱分析结果进行了讨论。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

晋城市煤炭加工利用现状、存在问题及发展建议

阐述了晋城市煤加工利用的现状 ,分析了煤炭加工利用存在的问题 ,提出了今后的发展建议     

鄱阳湖控制浅说

该控制工程主要效益是改变鄱阳湖“夏水冬陆”的现状，成为祖国名符其实的第一大淡水湖，水面与避署胜地庐山和历史名城南昌、景德镇等相连，改善沿湖环境，发展航运，增加水产，开发利用丰富的水资源和旅游资源使之与杭州西湖、瑞士日内瓦湖等并列为世界名湖。     

CMF300M355NU型质量流量计在油库汽车装车中的应用

介绍了质量流量计的工作原理有应用效果。这种新型质量流量计精度高，稳定性好，示值计量简便，可直接显示质量、流量、介质温度、密度等，维护量低，但必须正确安装、使用，才能发挥其应有的作用。     

浅谈如何搞好加油站的风险评价

阐述了加油站实施HSE管理，进行加油站风险评价的必要性，介绍了评价方法及其应用范围，评价组织的建立和工作流程及注意事项，指出：进行加油站风险评价，在选择评估方法时应从加油站的生产实际出发，针对不同的区域，采用适当的，可操作的方法；找出身边存在的危害因素，采取适当的措施来控制和化解风险，提高加油站安全管理水平，才能适应加入WTO后所面临的挑战。     

局部设有钢筋砼电梯井墙的设计探讨

本文就局部设有钢筋砼电梯井的工程计算及理论分析，阐明分析了少墙的框剪结构的设计及注意问题。     

数据采集与监控软件Genie

Genie是具有国际先进水平的数据采集与监控软件，它提供了一个面向对象的图形化用户界面，因此简化了数据采集过程、控制应用程序开发和操作员界面。本文介绍了Genie的特点、功能、基本用途以及VISUALBA－SIC在设计这类监控软件中的作用。