手机企业的标准化战略研究

介绍了标准化战略的重要意义,对国内手机企业标准化现状做了分析和剖析,并为企业提供了标准化战略工作的方法对策.     

Martensitic transformation of Ti50Ni30Cu20 alloy prepared by powder metallurgy

Phase transformation behavior of Ti50Ni30Cu20 shape memory alloys prepared by powder metallurgy is analyzed with respect to the duration of mechanical alloying. The processed blends were studied by differential scanning calorimetry and room temperature X-ray diffraction. The martensitic transformations evidenced by thermal scans are discussed in correlation with the relative phase content obtained from the refinement of the X-ray diffraction patterns.     

Experimental investigation and thermodynamic calculation of the phase equilibria in the Co-Nb-Ta ternary system

The isothermal sections of the Co-Nb-Ta ternary system at 900 °C, 1000 °C, 1100 °C, 1200 °C, 1300 °C have been experimentally determined by electron probe microanalysis (EPMA) and X-ray diffraction (XRD) techniques on the equilibrated alloys. On the basis of the experimental data investigated in the present work, the phase equilibria in the Co-Nb-Ta system has been thermodynamically assessed by using CALPHAD (CALculation of PHAse Diagrams) method, and a consistent set of the thermodynamic parameters leading to reasonable agreement between the calculated results and experimental data was obtained.     

Specific heat of the antiferro/ferro-magnet NpGa3

The specific heat of NpGa₃ has been measured for the first time. The magnetic transitions and more generally the full magnetic phase diagram have been re-established precisely. The Sommerfeld coefficient and the magnetic entropy point to a rather localized system, in agreement with previous studies, in particular high pressure Mössbauer and resistivity. The comparison with other NpX₃ suggests that NpGa₃ is the most localized member of the series.     

Study on Microstructure and Mechanical Properties of Hot Rolled Low Silicon Containing Phosphorus TRIP Steel

The effects of final air cooling temperature on the microstructure and mechanical properties of hot rolled 0.2C-1.9Mn-0.5Si-0.08P TRIP steel were studied by utilizing OM, SEM, TEM and tensile tests. Experimental results showed that in the multiphase microstructure of the investigated steel when the finish rolling temperature was about 820 ℃ and the final air cooling temperature was in the range of 630-700 ℃, the grain size of most of ferrite was finer (about 4 μm) and which had higher dislocation density, t...     

检定S型短型热电偶的4种不同冷端补偿方法之比较

检定长度在200～700 mm范围内的S型热电偶时,由于参考端温度大都处于室温或者波动的温场之中,需要将参考端温度恒定在0℃或采取修正、补偿等措施进行修正。现采取检定中最常用的4种不同的冷端补偿方法检定同一支S型短型热电偶,对结果进行比较分析,得到这4种不同的冷端补偿方法的优劣性及其准确度排序。结果表明,将参考端应用达到一等标准热电偶准确度水平的同极性热电偶丝延伸至参考端恒温器方法能获得较为理想的补偿效果。     

Investigation of Sn-Zn electrodeposition from acidic bath on EQCM

Tin-zinc (Sn-Zn) alloy with low tin content was deposited on gold electrode and steel substrate with use of chronoamperometric technique from an acidic bath. In order to evaluate coating efficiency of Sn-Zn alloy in 0.5 M NaCl solution, open circuit potential-time curve (E_OCP-t), polarization curves, mass change of the electrode (Δm-t) using quartz crystal microbalance (QCM) were compared to those of pure Sn and Zn coatings. Anodic stripping measurements were carried out simultaneously with the mass loss of the deposit. Scanning electron microscopy (SEM) and energy dispersive X-ray spectra (EDS) analysis were performed to characterize the surface morphology. Anodic stripping experiment and EDS analysis indicated that Sn, Zn, and SnO₂ formed on the electrode surface when Sn-Zn was coated from acidic bath. Furthermore, local mapping demonstrated homogeneous distribution of Sn and Zn atoms throughout the surface.     

Two milling time regimes in the evolution of magnetic anisotropy of mechanically alloyed soft magnetic powders

The milling time evolution of magnetic anisotropy of ball milled powders can be described considering two regimes. First, for short milling times, the main factor affecting the magnetic behavior of the alloy is the accumulation of internal stresses. Second, for long milling times, magnetic anisotropy can be explained using three contributions: long-range magnetoelastic, averaged short-range magnetoelastic and averaged magnetocrystalline anisotropies.     

新型钻镗刀的应用

介绍了一种新型复合刀具——ECOCUT钻镗刀,以及该刀具在数控加工中与普通刀具的综合对比情况.     

大宗物料激光精密盘库技术开发利用

大宗物料是指大型料场堆放的矿石、煤、球团矿等原料,因其堆积形状复杂、料场巨大等原因很难精确测量其体积。开发大宗物料激光精密盘库技术,总结实际盘库经验,着重对盘库的各项关键技术进行研究和探讨。