Surface nanocrystallization of commercial pure titanium by shot peening

The surface nanostructures of commercial pure titanium was realized by the modified shot peening equipment commonly used in industry through the special treatment process. The results show that high-energy-shot-peening(HESP) commonly used to prepare nanostructured surface layers can be achieved by the increase of pill size, pill speed, and treatment time in the commercial shot peening equipment. XRD, SEM and TEM were used to characterize the surface layer microstructure of treated specimens. The analytic results show that the main deformation mode of commercial pure Ti is twinning. At the beginning of deformation, the dislocations are formed and twins occur within or on plane, then twins in intersection plane appear, and at last the twin characteristics disappear in the surface layer after longer treatment time. The deformation layer depth increases with treatment time in a certain period when the pill size and speed are unchanged. And in the severe plastic deformation (SPD) layer in which the twins are not identified easily by using SEM, the nanocrystalline microstructures are found under TEM. The finest grain size in the surface layer is about 40 nm, and the depth of nanostructured layers is over 60 μm. The microhardness of the nanostructured surface layers is enhanced significantly after shot peening compared with that of the initial simple.     

Ti-Mo-Zr-Fe合金的微观结构与纳米压入特性的关系

通过不同的热处理制度控制TMZF合金中的相组成和含量，利用XRD分析确定各种相结构。利用纳米压入测量仪测试了不同组织结构下的硬度和弹性模量。结果表明，当合金中存在ω相时，合金的的硬度和弹性模量最高，随着热处理温度的提高，合金中的ω相消失，代之而来的是α相，而且越接近β转变温度，α相含量越少，对应的弹性模量和硬度越来越低。对于Ti—Mo—Zr-Fe合金来说压入性能（硬度、弹性模量）与相成分之间存在着良好的匹配关系。     

采用锥型砧座测定微小钢球的硬度及其方差分析

在WELSON－A653T洛氏硬度计上,采用自制凹锥形砧座测试微小钢球的硬度,解决了微小钢球在常用平面砧座和V形砧座上易打滑,不易固定,致使压头打在砧座上,损坏压头和砧座的难题,并采用方差分析的方法,将该法与传统试验方法相比较,验证其检测结果与传统法所获得检验结果无显著性差异。     

Improvement of wear resistance of plasma-sprayed molybdenum blend coatings

The wear resistance of plasma sprayed molybdenum blend coatings applicable to synchronizer rings or piston rings was investigated in this study. Four spray powders, one of which was pure molybdenum and the others blended powders of bronze and aluminum-silicon alloy powders mixed with molybdenum powders, were sprayed on a low-carbon steel substrate by atmospheric plasma spraying. Microstructural analysis of the coatings showed that the phases formed during spraying were relatively homogeneously distributed in the molybdenum matrix. The wear test results revealed that the wear rate of all the coatings increased with increasing wear load and that the blended coatings exhibited better wear resistance than the pure molybdenum coating, although the hardness was lower. In the pure molybdenum coatings, splats were readily fractured, or cracks were initiated between splats under high wear loads, thereby leading to the decrease in wear resistance. On the other hand, the molybdenum coating blended with bronze and aluminum-silicon alloy powders exhibited excellent wear resistance because hard phases such as CuAl₂ and Cu₉Al₄ formed inside the coating.     

Interaction between alloying and hardening of cast iron surface

To improve wear resistance of surface will increase the service life of gray cast iron directly.This paper presents that gray cast iron surface coated with alloy powder is locally remelted by TIG arc of increase the wear resistance.The influences of arc current and scanning rate etc on surface properties are found.Under different conditions.the microstructure,hardness and wear resistance of remelted layer are analyzed and measured.The results indicate that the gray cast iron surface can be strengthened by TIG arc local remelting treathent.Especially,surface alloying hardening effect is best and surface properties are improved remarkably.     

Microstructural and tribological behavior of TiAlN/MoS2-Ti coatings

1. Introduction The search for a better wear resistant coating has resulted in the development of a class of hard, solid-lubricated coatings. The driving force behind the coating industry was the need to develop a proc-ess that will extend the life of steel machine parts, cutting tools, molding dies, and sliding parts. For example, in the stamping industry, severe abrasive wear and galling (cold metal welding) are expected. There is the need for an efficient application of lu-bricants both for…     

国外先进的用于生产过程控制的硬度计及其新技术简介

提出了过程控制硬度计这一全新的概念,指出了作为过程控制硬度计应该具有的性能特点;全面地分析了国产硬度计同国际上先进的用于过程硬度控制的硬度计在性能和功能上的差距;介绍了作为国际上专门生产过程控制硬度计的瑞士ERNST公司的产品及其产品的特点,为国内硬度计的使用单位采购硬度计的选型,以及为硬度计的制造企业今后产品的研制方向提供了一个很好的参考.     

单晶SnO2纳米带裂纹形核的临界应力和断裂韧性

使用纳米压痕法测量了单晶SnO2纳米带的硬度、断裂韧性以及裂纹形核的临界应力。结果表明，当载荷大于临界值后微裂纹就从压痕顶端形核、扩展；与此相应，在载荷一位移曲线上出现位移突变平台，根据平台载荷计算出压痕裂纹形核的临界应力σc=3．4GPa；利用裂纹的长度计算出SnO2纳米带的断裂韧性为0．028—0．066MPa-m^1／2，其平均值为KIc=0．044MPa-rn^1／2，它比其它块体脆性材料的断裂韧性小一个数量级,实验测出SnO2纳米带的硬度H=6．25GPa和弹性模量E=86．7GPa。     

铝高速钢丝锥的应用

铝高速钢与普通高速钢的红硬性对比试验以及丝锥切削对比的试验研究表明 ,将铝高速钢用作螺纹工具—丝锥能明显提高其切削性能 ,从国内矿产资源角度看 ,开发使用铝高速钢具有其实际意义。     

AZ31镁合金表面液相渗铝的工艺与性能

采用液相扩渗技术在挤压态AZ31镁合金表面快速渗入铝，在合金表面获得过共晶渗层，并对渗层的成分、相组成、扩渗过程、纳米硬度和腐蚀性能进行分析。结果表明：AZ31镁合金在480℃热扩渗铝过程中发生了“熔化—凝固”变化，渗层为典型的过共晶组织：渗铝层含有Mg17A112相和镁的铝饱和固溶体，这种渗层具有较高的纳米硬度和较好的耐腐蚀性能；通过提高扩渗温度进行液相扩渗可以大大提高扩渗速度，但由于快速凝固收缩会造成表层产生起伏现象，控制冷却速度可以将表层起伏控制在可接受的范围。