铁路罐车密闭装车计量系统的运行分析

从中国石化股份公司济南分公司新上铁路罐车密闭装车计量系统的背景出发，阐述该系统的设计思想和组成；通过分析实际运行过程中仪表比对数据，讨论影响仪表贸易交接准确性的各种因素，提出相应的解决方法；最后通过铁路罐车密闭装车计量系统投用效果。证实该系统可产生明显的经济效益。     

岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

一个新颖的轮廓线跟踪算法

提出了一个新颖的基于隐马尔科夫模型与光流的轮廓线跟踪算法。曲线描绘由B样条形状空间向量来表达,能够捕捉全局和局部变形。提出应用沿曲线的光流计算来预测曲线在下一帧的位置,在预测曲线的基础上,提出应用隐马尔科夫模型来准确定位曲线的位置。隐马尔科夫模型提供了一种有效的概率手段来融合多种量测特征比如边缘,曲线平滑性,区域灰度或颜色统计信息等等,能够更准确的定位曲线位置。基于仿射形状空间的实验了表明本文所提出算法的有效性。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

Collection Conduits Including Subsurface Drains

Numerous types of pipes and channels with spatially increasing flows in environmental engineering applications are identified by type and function and referred to as collection conduits. An overview of methods for designing and analyzing collection conduits is provided. Full conduits with nonuniform and uniform inflow are first considered. Dimensional analysis is then employed to demonstrate the relationship between variables for open channels; that leads to the identification of possibilities for generalized numerical solutions. Prior collection conduit applications are discussed within the framework of the dimensional analysis (which also pertains to some constant-flow applications). A previously unpublished generalized numerical solution for rectangular collection conduits is presented. Subsurface drains are addressed with particular emphasis, including the use of numerical methods to develop a new generalized chart and relation to other design methods. Among the important conclusions for subsurface drains is that the somewhat common practice of using Manning’s equation alone for such problems is not generally adequate. Examples and practical design suggestions are included, and the use of computer-based numerical methods is discussed more generally.     

大型连杆流线简易试验方法

介绍了一种大型连杆流线的简易试验方法及其评价原则。该方法可清晰显示流线，并适合任何尺寸和形状的锻造连杆的流线试验。     

哈得4联合站技术改造

位于塔克拉玛干大沙漠腹地的哈得4油田,2004年成为全国最大的沙漠油田,2005年产量达到200×104t。在对联合站存在问题逐一分析的基础上,提出了技术改造的措施。现场采集的运行数据表明技术改造效果明显,增强了流程可靠性,提高了自动化水平,降低了能耗。     

自喷井电动清蜡绞车的研制

针对目前石油钻采用清蜡绞车总体结构设计不合理以及实用性不强等技术难题,研制开发了自喷井电动清蜡绞车。该绞车的核心部件包括过载保护安全装置、牙嵌离合器轴套、自动/手动互换装置、计量装置以及密封装置。在清蜡绞车自动工作中,当清蜡刮刀遇到较大阻力时,清蜡绞车将接收到反馈信号,可实现智能停车,自动转换为手动状态,以便操作人员检查和排除故障,从而确保了操作的安全性,延长了设备的使用寿命。1000余台电动清蜡绞车的现场应用表明,该产品可以大大降低原油的开采成本,具有良好的经济效益和社会效益。     

The influence of plastic properties on chip formation

A two-dimensional finite-element model of the chip formation process is used to study the influence of the material law determining plastic flow on chip formation of titanium alloys at high cutting speeds. For simplicity, friction and thermo-mechanical properties of the tool are neglected in the simulations. Titanium chips are strongly segmented and therefore especially suitable to study the role of segmentation for the cutting force and other cutting parameters. Of special interest is the influence of the thermal softening parameter in the material law. Increasing thermal softening leads to a drastic decrease in the cutting force and a corresponding increase in chip segmentation. A variation of the hardening exponent is also performed. It is shown that the simulation results can be understood by using adiabatic flow stress curves. The variation of the hardening exponent leads to strongly differing chip shapes, although the cutting force stays nearly constant. This shows that mean cutting forces should not be used as simulation verification parameters.     

土石过水围堰过水期最不利工况及其流量确定

本文系统分析了影响土石过水围堰溢流工况的主要因素，提出衡量最不利工况的指标和确定员不利流量的方法，为土石过水围堰堰体下游护坡结构及消能防冲设施设计提供了理论依据。通过理论计算结果与模型试验现场观测资料数据对比分析，说明提出的过水期最不利流量判别方法是符合实际情况的。