油煤浆的管道输送特性与管路设计原则

通过理论分析和管道实验，探讨了油煤浆在工业管道输送中的流变特性、流动状态和阻力特性，得出了油煤浆的物性参数、表观参数、管道阻力参数的测定值和计算公式，并在此基础上探讨了油煤浆管道输送的设计原则，为油煤浆管路的设计提供基础数据、计算方法和一般原则。     

CX6112车铣复合机床设计方案的研究与探讨

文章较系统地论述了车铣复合机床设计方案的形成过程，同时分析了该设计方案的持点，并简要介绍了该产品的主要技术参数和用途，简评了该产品的技术水平。     

Characteristic Investigation of Nano-Crystal Hydrogen Storage Alloys

A Ml (NiCoMnA1)5 hydrogen storage alloys was prepared by double-roller rapid quenching.Its microstructure, electrochemically and kinetic characteristic were studied.A uniform crystal phase with CaCu5 structure could be detected by XRD analyses, whose average grain size is 30 ～ 50 nm and the ratio of c/a of nano-crystal hydrogen storage alloy is larger.The hydrogen absorption/desertion p - C isotherms of alloy show that its fiat-performance is perfect and the magnetic stagnant effect is very little.An simulate cell is used for electrochemical measurement.Electrode is 10C, the capacity decreasing rate via the 450 cycles at 7C is less than 20%.     

厅堂音质评价参量的相关性分析

当代室内声学专家经常选用的评价厅堂音质的物理参量，其间有几个量是相关的。作为室内音质设计的依据．必须寻找基本相互独立的参量，才有更大的实用意义。     

利用Love波特性计算地基动力响应

本文利用Love波弥散特性在频域上对地基出平面振动及扭振问题进行了研究。在计算区域内结构将采用有限单元划分,而在边界上则根据Love 面波特性使用传递边界有限单元。本文同时讨论了不同模态波对结构动力响应的贡献。本文方法也适合于静力分析。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

混流,定浆式转轮特性参数的计算机处理

本文根据混流、定浆式转轮特性多数的特点建立了一种能将高维特性多数用一个具有二阶连续导数且保形的函数给予表达的方法，它的精度高，且能方便生成满足各种用途的特性曲线。     

水泵水轮机的数值模拟及其应用

采用足够小的直线段拟合机组全特性曲线平直部分，采用二次多项式拟合机组全特性曲线弯曲部分，推导了有关方程，并对模拟的方程进行了处理，编制了较通用的计算机程序，利用该计算机程序对我国蒲石河抽水蓄能电站进行了计算分析，计算结果表明：该计算机程序计算速度较快、计算准确度较高，提出的水泵水轮机的数值模拟方法具有实用价值．     

特征线法分析长距离输油管道的流动瞬变过程

本文建立了基于特征线方法求充动瞬变过程的数值模型，编制了针对长距离输油管道流动瞬变过程的分析软件。在数值处理上，Ｄａｒｃｙ＝Ｗｅｉｓｂａｃｈ摩擦力项用二阶精度格式来近似，因此保证了高粘度流体在流动瞬变过程分析时的计算稳定性和精确度。模型考虑了埋管地形对沿线瞬变压力的影响，当某一泵站发生水击后其它站的反应同其上控程序确定。应用该软件，分析模拟了某一长距离输油管道在中间泵站停电或末站瞬时关阀情况下的流     

气门用4Cr9Si2钢调质工艺研究

采用正交试验 ,研究了 4Cr9Si2钢的淬火温度、回火温度与组织、硬度间的关系 ,得出了最佳的工艺参数 (10 10℃淬火 ,6 0 0℃回火 )。实际生产表明 ,采用此工艺后 ,断裂现象基本消除 ,气门的热处理质量有了明显提高。