薄板坯连铸浸入式水口结构数值模拟

使用有限元计算方法开展薄板坯连铸浸入式水口流场的研究 ,分别对水口不同浸入深度的流场分布、水口出口不同角度的流场分布进行计算。结果发现 :水口的浸入深度在 30 0mm时较为合理 ;水口的出口角度以R1 5、60°、45°为宜     

Surface modification of tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) by plasmas for copper metallization

Tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) sheet surfaces were modified with argon, helium, oxygen, and hydrogen plasmas. How the four plasmas modified the PFA sheet surfaces was investigated. All plasmas modified the PFA surfaces and at the same time initiated degradation of the PFA polymer chains. The balance between modification and degradation was strongly influenced by the magnitude of the discharge current in the plasmas. Efficiency of the plasmas in modification was hydrogen plasma > oxygen plasma > argon plasma > helium plasma. The modification involved defluorination of CF₂ carbons into CHF and CH₂ carbons and oxidation into O? CH₂, O? CHF, and O? CF₂ groups. The surface‐modification technique (a combination of hydrogen plasma treatment and silane coupling treatment) proposed in this study was applied for copper metallization of the PFA surface. The utility of the technique was confirmed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1087–1097, 2002     

臭氧氧化处理法对聚丙烯表面涂装性的改良 Ⅳ.聚丙烯表面亲水性和涂膜剥离强度的关系

讨论了用臭氧氧化法对聚丙烯表面进行涂装性改良时,丙烯均聚物、乙烯-丙烯嵌段共聚物及无规共聚物表面以接触角表示的亲水性和涂膜剥离强度之间的关系。结果表明,当聚丙烯表面对水的接触角在84°附近时,可反应型涂料的涂膜剥离强度将出现最大值。在此也证明了涂膜的剥离破坏存在着接着破坏和凝集破坏两种机理,当接触角减小到84°及84°以上时,剥离发生在聚丙烯和涂层的界面上产生接着破坏;当接触角减小到84°以下时,剥离发生在聚丙烯的表面氧化层相中,产生凝集破坏。     

High resolution solid state 13C n.m.r. of butadiene grafted polypropylene

¹H dipolar decoupled ¹³C n.m.r. experiments with the aid of the magic angle spinning technique have been used to determine the graft content and the isomer content of the polybutadiene grafts in a graft copolymer with isotactic polypropylene.     

植被排列方式及坡度对坡面流Fr影响的试验研究

为探究植被的排列方式及坡度大小对坡面流弗劳德数Fr的影响,以期揭示坡面流弗劳德数Fr的内在规律。利用人工模拟试验,系统研究了6个坡度、3种植物排列方向与水流方向呈不同走向角的条件下Fr与单位底面积的空间摩阻表面积K值的特征关系。表明在非淹没状态下,Fr与K值的关系为随K值的增大Fr呈现先减小后趋于平稳的趋势;Fr的取值随坡度的增大而增大;在一定的坡度范围内,同一坡度下,当Fr1时,同一K值下,走向角越大对应的Fr值越小,当Fr1时则相反;同一走向角下,在同一K值下,坡度越大对应的Fr就越大。得出在坡度一定的条件下,坡面植被的排列方式不同,弗劳德数Fr的取值也不相同;坡度是影响Fr取值范围的重要因素之一。     

The effect of Al content on the wettability between liquid iron and MgOAl2O3 binary substrate

In the present study, the wettability between liquid iron with two different Al contents and MgOAl₂O₃ binary substrates was studied in reducing atmosphere. The contact angles between liquid iron with 18?ppm Al and MgO, MgO·Al₂O₃, Al₂O₃ were 133.5°, 113.7°, 126.9° respectively. With the variation of the substrate composition, the contact angles for the intermediate binary phases of the three components (MgO, MgO·Al₂O₃, Al₂O₃) obeyed the Cassie theory. In the experiment using iron with 370?ppm Al, all the contact angles were higher than that using low Al-containing iron. The surface of the iron drop was covered with an oxide layer, which mainly consisted of many small particles. With the variation of the substrate gradually from MgO to Al₂O₃, the composition of the oxide layer changed from MgO·Al₂O₃ to CaOAl₂O₃. The formation of the oxide layer prevented the spreading of liquid iron, leading to the increase of the contact angle.     

聚合物熔体在圆锥短口模的挤出胀大方程

深入讨论了聚合物熔体在不同长径比、不同角度圆锥短口模的挤出胀大现象及机理，利用生产用挤出机进行不同角度的圆锥短口模实验。结果表明，圆锥短口模挤出过程中，熔体在收敛流道受到拉伸流变，导致强烈的入口弹性效应，表现为熔体在短口模挤出时显著的挤出胀大。理论和实验研究结果进一步表明不同圆锥口模入口角对实验材料表现出有不同的挤出胀大值。     

陶瓷窑炉用高精度温度测量仪的研制

研制了一种可直接测量热电阻和热电偶输入的高精度温度测量仪，介绍了它的硬件和软件构成，研究了前置放大电路的设计和测量数据的软件非线性补偿方法，实际应用表明，该测量仪具有较高的测量精度。     

低氟含量低表面能自清洁氟碳涂料的研究

以氟单体和丙烯酸酯类单体通过聚合物的分子结构设计，合成了一类总氟含量不超过12％的低氟含量的含氟丙烯酸树脂，所制备的氟碳涂料的涂层的表面能低，具有自清洁功能。分析了该涂层中极性与非极性官能团的分子取向机理，测定了纯水水珠在不同含氟单体均聚物和共聚物清漆漆膜上以及在含氟丙烯酸树脂涂层上的接触角，探明了含氟丙烯酸树脂涂层的总氟含量与表面能的关系、含氟官能团在涂层中的分布，探讨了低氟含量的含氟丙烯酸树脂涂料的涂层自清洁机理。     

基于光学测角和无线数据传输技术的传递对准

为了解决动基座传递对准中航向角估计困难的问题,提出了基于光学测角和无线数据传输技术的传递对准技术方案。通过对航母舰体挠曲变形模型的建立和对光学测角原理的分析,构建了相应的卡尔曼滤波器。仿真结果表明,利用卡尔曼滤波能够估计出姿态误差角和光学测量装置自身的等效零偏。当对光学测量装置的等效零偏补偿之后,航母在匀速航行条件下,姿态误差和速度误差都可以得到快速的收敛,其中航向角误差可以在4 s内收敛到0.7'以内,明显提高了子惯导航向角的对准速度。