Lattice structure on some fuzzy algebraic systems

In this paper, we study the lattice structure of some fuzzy algebraic systems such as (G-)fuzzy groups, some fuzzy ordered algebras and fuzzy hyperstructures. We prove that under suitable conditions, these structures form a distributive or modular lattice. This research partially is supported by the “ Fuzzy Systems and its Applications Center of Excelence, Shahid Bahonar University of Kerman, Iran”.     

Evaluation of passive microwave snow water equivalent algorithms in the depth hoar-dominated snowpack of the Kuparuk River Watershed, Alaska, USA

This research investigates the utility of passive microwave remote sensing instruments to accurately determine snow water equivalent (SWE) over large spatial extents. Three existing Special Sensor Microwave Imager (SSM/I) snow water equivalent algorithms produced by Chang, Tait and Goodison were evaluated for their ability to determine snow water equivalent in a snowpack containing substantial depth hoar, large faceted snow crystals. The Kuparuk River Watershed (8140 km²) test site on the North Slope of Alaska was chosen for its snowpack containing a think depth hoar layer and long history of ground truth data. A new regional snow water equivalent algorithm was developed to determine if it could produce better results than the existing algorithms in an area known to contain significant depth hoar. The four algorithms were tested to see how well they could determine snow water equivalent: (1) on a per pixel basis, (2) across swath-averaged spatial bands of approximately 850 km², and (3) on a watershed scale. The algorithms were evaluated to see if they captured the annual spatial distribution in snow water equivalent over the watershed. Results show that the algorithms developed by Chang and from this research are generally within 3 cm of the spatially averaged snow water equivalents over the entire watershed. The algorithms produced by Chang, Tait, and in this research were able to predict the basin-wide ground measured snow water equivalent value within a percent error range from −32.4% to 24.4% in the years with a typical snowpack. None of the algorithms produce accurate results on a pixel-by-pixel scale, with errors ranging from −26% to 308%.     

透反液晶显示器

兼有透射型和反射型液晶显示优点的透反液晶显示可工作于透射和反射两种显示模式，它将广泛应用于手机、PDA等通讯领域。透反液晶显示可分为单盒厚和双盒厚两大类。又可分为扭曲型和非扭曲型两种。为了研制出高性能透反液晶显示器，需解决透反两个显示区的响应时间、光效率、色饱和度的差异以及视角等问题。文中介绍了Sharp公司开发的2种基本的透反液晶显示。以及3种新近开发的高性能透反液晶显示。随着应用市场的扩大和技术的进步，透反液晶显示将会进一步得到发展。     

关于本地传输网网络优化的探讨

根据长期工作经验,对现有网络存在的问题进行分析,提出对本地传输网网络优化的有关建议。     

一种新的变步长ICA自适应算法

结合互信息极小的优化判据，基于估计函数期望平方准则、外点法和最速下降法的思想，本文导出了一种新的变步长独立分量分析(ICA)自适应算法。该算法克服了固定步长在分离矩阵推导过程中出现的稳态失调问题，比基于模拟退火步长的ICA算法有更快的仞始收敛速度和较高的分离精度。同时，该算法还具有较好的时变系统跟踪能力。理论分析和仿真计算结果证实了其可以有效地提高ICA的自适虚性，更准确地完成盲信号分离。     

Numerical analysis of two-dimensional steady-state and transient heat transfer in a parallel duct filled with pressurized He II

Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified.     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Understanding and Modeling the Effect of Surfactants in Enhanced Particle Removal from Surfaces in Aqueous Media

The removal of particulate contamination is a critical issue for many manufacturing processes. It is particularly critical to the electronics industry in which small pieces of microscopic debris remaining after chemical mechanical planarization (cmp) using submicron polishing particles can cause device failure. One way to enhance particle removal following the cmp process is to utilize surfactants. Recent research has shown ways to model the effect of surfactants on enhanced particle removal. However, previous research has not demonstrated the effect of ionic strength on enhanced particle removal associated with surfactant use. Past research has also not shown the combined effects of ionic strength and surfactant concentration on enhanced particle removal using surfactants. This article summarizes the parameters affecting particle removal, and it provides data and analysis on the effect of ionic strength as well as the combined effects of ionic strength and surfactant concentration on particle removal following cmp processing.     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.