环境友好水基润滑添加剂的研究

在脂肪酸分子中引入硼和氮，合成了一种环境友好水基润滑添加剂BNR，并利用红外光谱对其主要官能团进行了表征。通过四球试验机考察了BNR添加剂在水中的抗磨性能与极压性能，用X射线光电子能谱仪对磨痕表面元素进行了分析，探讨了该类添加剂的极压抗磨作用机理。结果表明：硼氮化水基润滑添加剂BNR在水中具有优良的抗磨和减摩性能；其润滑作用机理是由于长链脂肪酸分子的载体作用、硼的缺电子性、氮的高反应活性以及三者的协同作用与摩擦金属表面形成了一层高强度的吸附膜和／或摩擦化学反应膜。     

磨损自补偿添加剂在成品油中的摩擦学效应

利用四球试验机考察了二聚酸－3－氯－2－羟基丙单酯（DAE）在4种成品油中的摩擦学性能。试验结果表明，DAE添加剂在L－HM68液压油和L－DAB100空压机油中具有良好的适应性，使其承载能力增强，摩擦系数降低及耐磨性增强；DAE在L－CKE涡轮蜗杆油中使耐磨性增强；DAE在L－CKC150齿轮油中虽使承载能力提高，减磨性增强，但有使耐磨性减小的趋势，说明DAE在不同的油中有不同的性能。     

两种不同界面结合强度碳/铝复合材料的内耗特性

本文研究了两种不同界面结合强度的碳/铝复合材料经不同次数加载热循环处理后的内耗值及内耗机制。弱界面结合的C/L2复合材料的内耗值变化主要由界面脱粘引起,而强界面结合的C/LD2复合材料的内耗值变化主要由位错运动所致。     

Tribological issues in reducing piston ring friction losses

In this paper improvement in fuel economy by reducing piston ring friction is studied and reduction of piston ring tension and the use of two-ring packages are found to be effective. However, these can be accompanied by adverse effects such as excessive wear and increasing oil consumption, and measures to overcome these problems are studied in detail.     

含硫氰基团化合物的摩擦学性能及其摩擦化学机理研究

以三烷基磷酸酯络合硫氰酸钙为模型化合物研究了含硫氰基团的络合物的摩擦学行为，发现它有高的承载能力，良好的抗磨减摩性。用俄歇能谱（ＡＥＳ）、Ｘ－射线衍射（ＸＲＤ）、扫描电镜（ＳＥＭ）及Ｘ－射线能谱（ＥＤＸ）研究了摩擦表面元素组成及其可能物相。探讨了摩擦化学机理，认为化合物中的硫氰基团对摩擦学性能起主要作用，并在摩擦过程中发生类似于化学热处理中的硫氰共渗。     

连续驱动摩擦焊动态扭矩检测的新方法—VCMM法

连续驱动摩擦焊动态扭矩检测的新方法──ＶＣＭＭ法刘金合，罗键连续驱动摩擦焊扭矩是一个重要的工艺参数。摩擦焊扭矩是动态扭矩，具有时变性、速变性以及变化范围大等特点。现有的检测摩擦焊扭矩的方法均有一定的局限性’‘－’‘，本文提出了通过驱动主电机定子电压和...     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

聚醚合成工业齿轮油的研制

以聚醚为基础油辅以抗磨剂、抗氧剂、防锈剂等多种添加剂研制而成的KGW聚醚合成工业齿轮油具有优异的黏温性能和低温性能，优异的极压抗磨性，极优的减摩性能，可满足高负荷、强冲击等苛刻条件下各类齿轮传动装置的润滑要求。该系列产品达到国外同类油品质量水平。     

宽带激光熔覆WCP/Ni基合金梯度复合涂层组织与摩擦磨损特性

研究了铸造WC_P/Ni基合金梯度复合涂层组织与摩擦磨损特性。结果表明,梯度复合涂层与基材实现了良好的冶金结合,涂层内有γ-Ni枝晶组织,γ-Ni＋M₂₃C 6共晶组织以及凝固结晶析出的M₆C、M₂₃C₆、M₇C₃等块状或条状组织;随着铸造WC_P体积分数的增加,复合涂层摩擦系数减小,耐磨性增加。19-4试样的耐磨性最高值为4.61,是基材的3倍以上。梯度涂层的磨损机理为磨粒磨损与粘着磨损的复合作用。     

Time and Temperature Factors in Construction of Rock Strength Criteria

Using the synthesis of the kinetic concept on solid strength and the Coulomb - Mohr strength theory as the base, the failure conditions taking into account the time and temperature factors are obtained.