混凝土小型砌块建筑裂缝宽度的标准设置研究

通过对混凝土小型空心砌块单片墙进行试验 ,了解不同构造措施墙体的初始裂缝在墙体上出现的部位、形态、发展规律以及墙体最终破坏形态 ,并通过试验明确墙体在不同受力状态下的裂缝形态 ,最后根据试验结果初步提出混凝土小型空心砌块建筑的裂缝宽度控制标准     

中厚板表面质量分析

在对济钢中厚板各种表面缺陷产生原因和几率进行综合分析的基础上 ,将缺陷分为 3类 :A类(折叠、麻点、划伤等 )、B类 (夹杂、结疤、分层 )、C类 (裂纹 ) ,重点对裂纹缺陷进行探讨 ,并提出了相应的改进措施。     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。     

激光晶体Nd:YVO4的形貌及生长缺陷

本文报道了应用环境扫描电镜（ESEM）和同步辐射X射线白光形貌术对采用提拉法生长出的Nd:YVO4晶体进行的形貌及生长缺陷的分析,获得了该晶体的开裂表面的ESEM形貌像以及取自晶体肩部和中间部位的（001）面的同步辐射白光形貌像,观察到了位错、包裹物等缺陷,可为生长高质量的Nd:YVO4晶体提供重要的启示.     

钢筋混凝土圆形水池裂缝分析与处理

本文针对某钢筋混凝土圆形水池在使用过程中出现的裂缝进行计算和分析，讨论了温度对水池的影响，特别是考虑储水区与非储水区存在温差的条件对水池池壁裂缝的影响，并提出处理方案。     

共晶碳化物团球化对铸铁激光熔敷层抗裂性的影响

为提高铸铁表面大面积激光熔敷层抗裂性问题，通过冶金因元素控制熔敷层组织形态在熔敷材料中加入碱金属元素钾，研究了在激光快速加热条件下钾对铸铁激光熔敷层组织团球化的影响，进而分析了该球状组织对熔敷层抗裂性的影响，结果表明随熔敷金属内钾含量增多熔敷层内共晶碳化物组织呈球状及孤岛状，这种组织明显提高了熔敷层抗裂性，此外大量的渗碳体组织确保了熔敷层具有较高的耐磨性；获得了无裂纹的大面积搭接熔敷层，其对应合金系统为Fe-C-Si-Ni-K。     

蓝疆号起重铺管船托管架拖挂结构的质量及进度控制

蓝疆号起重铺管船是一艘集起重、管道铺设于一身的多功能新型船舶,在铺管作业系统中,设有一连接船体与托管架的独立结构——拖挂结构。介绍这个由特厚高强钢板组焊而成的结构在制造过程和现场施工中的质量控制及进度控制,供从事工程管理人员参考。     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

Numerical simulations of specimen size and mismatch effects in ductile crack growth - Part II: Near-tip stress fields

The effect of ductile crack growth on the near tip stress field in two different specimen geometries has been investigated. For homogeneous specimens it is observed that the peak stress level increases with ductile crack growth. The effect is most pronounced up to about 1 mm of crack growth. For low and intermediate hardening there is a significant effect of specimen size on the stress level. In case of mismatch in yield stress, the simulations show that the increase in stress level in the material with the lower yield stress is of a similar magnitude as is the case for stationary cracks. In case of ductile crack growth deviation from the original crack plane occurs, the highest stresses are still found close to the interface, and not in front of the current crack tip.