提高中高含水期油井压裂经济效益的方法

为提高葡北油田中高含水期油井压裂经济效益，合理选择压裂井层尤为重要。应用水驱特征曲线预测出油井压裂前可采储量，从而计算出剩余可采储量及可采储量采出程度，通过绘制油井压裂前剩余可采储量及可采储量采出程度与油井压裂后所创经济效益之间关系曲线，寻找出相关规律，进行优选压裂井，再根据精细地质研究成果，在剩余油富集区选择具体压裂层位。经实际应用，取得了较好效果，提高了油井压裂方案符合率，提高了经济效益，进而总结出一套适合葡北油田中高含水期油井压裂选井选层方法，对今后进一步搞好油井压裂增产工作具有指导意义。     

Effect of thermophoresis on particle deposition rate from a natural convection flow onto a vertical wavy plate

This research discusses the impacts of the surface area that the wavy surface gets more than the flat plate upon the aerosol particle deposition. Starting from the full Navier–Stokes equation, the mathematical analysis takes the thermophoretic motion formed by the temperature gradient and the fluid thermal expansion into consideration, and converts the governing equations into the boundary layer equation by the simple coordinate transformation and non-similarity method, and then works out these equations by the Spline Alternating-Direction Implicit method (SADI). The numerical value result reveals that the average deposition effect of the wavy plate is greater than the flat plate and that the increasing rate is nearly equal to the value obtained by dividing the surface area that the wavy plate gets more than the flat plate by 2.2.     

1270轧机弹性曲线的回归及参数估计

首先介绍了轧机弹性曲线的基础知识及 1 2 70轧机AGC系统的基本结构 ,然后论述了数据采集的方法 ,最后根据最小二乘法得到轧机弹性曲线的回归模型及刚度系数的实验结果。     

Step response classification for model-based autotuning via polygonal curve approximation

A model-based autotuning method consists of an identification and a regulator tuning phase. To achieve satisfactory performance and robustness, it is advisable that both phases be tailored a priori to the characteristics of the observed process dynamics. Such characteristics include, but are not limited to, the model structure. For example, overdamped and underdamped models with the same pole-zero structure are parametrised and controlled in different ways. Step response data, that are typically used for the identification phase in the autotuning context, can also be pre-processed to reveal those characteristics. This paper presents a step response classification method suitable for the above purpose. The method is based on a polygonal curve approximation technique for data pre-processing, followed by a neural network classifier. Only normalised I/O data are employed, so that the neural network can be trained off-line with simulated data. Simulation results are reported to show the effectiveness of the proposed classification method in terms of the achievable tuning results.     

误读与纠正

分析材料试验机度盘偏转角度小 (准确度低 )、试样打滑、定义 (上屈服强度 -下屈服强度 -屈服强度 )模糊、不同应力速率等导致误读 ,并针对误读原因提出纠正方法。     

砼受压损伤力学本构模型的研究

本文利用ＭＴＳ公司８１５．０２型电液伺服试验系统对砼进行了等应变速率加载控制的应力一应变全曲线试验，应用不可逆热力学和内变量理论的成果建立了砼损伤力学模型，并用概率统计的观点分析了损伤的演化规律。由于考虑了不可逆变形的影响，本文所建本构模型与实验吻合较好。     

混流,定浆式转轮特性参数的计算机处理

本文根据混流、定浆式转轮特性多数的特点建立了一种能将高维特性多数用一个具有二阶连续导数且保形的函数给予表达的方法，它的精度高，且能方便生成满足各种用途的特性曲线。     

工业固体核磁Magmonitor用于聚烯烃质量参数测试方法的建立

利用实际采集的系列试样 ,在工业固体核磁Magmonitor(IMR)上建立了标准曲线 ;在IMR上运行标样的核磁信号后 ,对FID信号与实验数值之间的匹配使用 32个误差分析因子进行分析 ,并在Cregcon软件下运行回归分析 ,将结果转化成仪器预测模型。结果表明 ,测试相对偏差在 10 %以内 ,数据重现性好 ,而粉料与共聚物的测试误差有待改进。将IMR测试结果与不同测试方法进行比较 ,建议测试前对粉料进行脱气与脱水处理     

MOS结构准静态测试中的异常C—V曲线

本文报导了MOS结构在准静态测试中的异常电容-电压曲线。讨论了它们产生的原因。     

Spline-regression estimation of the influence of exposure dose on cancer probability

Spline regression is used to analyze the influence of radiation on the cancer probability in a group of participants of Chernobyl accident mitigation, depending on the exposure dose. A new method is proposed to approximate modified polygons by linear splines with two nodes. An algorithm for the identification of a transition point is outlined. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 3, pp. 168–176, May–June 2006.